2 wireless router bridging settings

The route for the upstairs is the route for the downstairs A is B

Route A enables the Bridge function. Enter the mac NIC address of Route B in the mac address of the AP. Set the wireless channel

Channel 10. Lan ip address; when the subnet mask of 192.168.1.1 is 255.255.255.0, disable wireless encryption in the vro)


Enable the Bridge Function for Route B, enter the mac NIC address of route A in the mac address of the AP, and set the wireless channel

Channel 10. Lan ip address; Disable 192.168.1.2 when the subnet mask is 255.255.0.0.

Wireless encryption of routes)


Route A is the main route connecting the cat. Route B is placed in A place where the signal is received, but not completely

No signal. This is used downstairs. To set the wireless network card in this book, the manual IP address is 192.168.1.3 subnet mask is 255.255.255.0 gateway 192.168.1.1 DNS server IP192.168.1.1, and thus a dual-route Wireless AP is connected!

If route B fails to receive the signal of route A at any time, the LAN interface settings of Route B from the LAN port of route A will not change.

Method 2: do not set the router LAN address)

During this time, I was working on campus wireless network construction and encountered a problem: After the wireless routing is bridging, I can connect to the router through a network cable, but I cannot connect to the Internet through a wireless network card, finally, I found the problem was that DHCP of a wireless router other than vrouters 1 must be disabled. The following describes the configuration process.

Point-to-Point wireless bridging Configuration
Device Name: Wireless Broadband Router
Brand Model: TP-LINK TL-WR340G +
Number of devices: 2

View the wireless MAC address of a wireless router:

Vro1 1 Configuration:
1. Enter "192.168.1.1" in the address bar, and then in the pop-up window, enter the default username: admin Password: admin
2. In the WAN port settings, set the current Internet access method, in this example, PPPoE dialing.
3. Set the basic wireless information, change the default SSID to AP1, enable the Bridge function, and enter the wireless MAC address of ap2.
Vrouters 4 and 1 are enabled

========================================================== ======================================
Vro2 2 Configuration:
1. Enter 192.168.1.1 in the address bar, and then enter the default account: admin. default password: admin.
2. in LAN port settings, change the IP address of the LAN port to 192.168.1.2, and click "save ".
3. The WAN port settings remain the default value.
4. In the Basic settings of "Wireless Parameters", change the SSID to AP2, enable the Bridge function, and enter the MAC address of AP1 in the following box.
5. In the DHCP service settings, vro2 2 disables the DHCP service. Click "save ".

The basic configuration of point-to-point wireless bridging is complete. Connect to AP1 or AP2 using a wireless client!

========================================================== ==========================================================

If you do not want unauthorized users to access our AP, enable security settings in the basic configuration of "Wireless Parameters". The encryption type only uses the default WEP, and the key format is ASCII code, the key type can be set to 128-bit or 64-bit as needed. Here, the key type is 64-bit. Password: loveu
The encryption of AP1 and AP2 must be configured, and both sides are configured the same)

========================================================== ====================================

Point-to-Point wireless bridging Configuration
Device Name: Wireless Broadband Router
Brand Model: TP-LINK TL-WR340G +
Number of devices: 5

The new version of TP-LINK 340G + and 541G + support point-to-point wireless bridging, also support point-to-point wireless bridging.
Configuration point-to-point wireless bridging is similar to point-to-point wireless bridging.

1. The configuration of AP3, protocol, and AP5 is the same as that of AP2. In the basic configuration of "Wireless Parameters", fill in the wireless MAC address of AP1 and disable the DHCP service, only DHCP of AP1 is enabled.
2. In the basic configuration of AP1's "Wireless Parameters", enter the wireless MAC addresses of AP2, AP3, protocol, and AP5.
3. All Wireless AP channels are the same, and the SSID is different.

Point-to-Point wireless bridging is complete. Connect to AP1-AP5 using a wireless client!