ADSL Router installation: About Datang Telecom and UT Zhukang

The following is the ADSL Router installation on Datang Telecom A-400 to open the routing and UT Kang ADSL Router installation of detailed introduction, read the article today, you will be familiar with Datang Telecom A-400 to open the routing and UT Kang ADSL Router installation method.

In the edit box, enter the Ethernet port IP address of the adsl modem. If this item is not changed during the first configuration or configuration, the default value on the interface is the correct IP address. If you have modified this item, enter the last modified value). Make sure that the value is correct. Otherwise, the MODEM cannot be connected through the configuration program and cannot be configured. If the user forgets the IP address of the network port, press the "RESIP" button on the device backboard to restore the IP address of the factory-configured network port (192.168.10.1 ).

During the first operation, the default value of adsl modem is 192.168.10.1. You need to change the ip nic address of the PC to the IP address of the same network segment, and then modify it from the configuration program as needed. After filling in the IP address, click "Next ". After the program and the ADSL Router are successfully installed, the program reads the status and parameters of the current ADSL and displays the interface shown in the following figure: You can choose the encapsulated protocol provided by China Telecom ), the following protocol types are available: RFC1483 BRIDGE: Single-host bridging. In this way, only one client can be connected to the WAN through an adsl modem in bridging mode.

RFC1577 ROUTER: IPOA access. In this way, a client can access the WAN through an adsl modem in IPOA mode, or several clients can connect to the WAN through a HUB through an adsl modem in IPOA mode. RFC2364 ROUTER: PPPOA access. In this way, a client can be connected to the WAN through an adsl modem in PPPOA mode, or several clients can connect to the WAN through a HUB through an adsl modem in PPPOA mode. If you want to route the Internet, select RFC2364 ROUTER.

On this interface, you can complete the configuration of the PVC parameter for the adsl modem. Enter 32 for the VCI of a friend in Wuhan. The PPPOA protocol is used on the ADSL Wan port, you do not need to set the line IP address or line subnet mask. It will be dynamically allocated a line IP address when dialing the internet. Therefore, you only need to enter the Internet port IP address of the adsl modem in the edit box on this interface (you do not need to modify it for Wuhan friends) and the dialing Internet user name and password provided by China Telecom. After entering the parameters, click "finish". The configuration program begins to configure the parameters for the adsl modem. A message box is displayed after the configuration program completes the configuration of the adsl modem.

Datang Telecom A-400 open Routing

Because there are no more cats at hand, we can only take this as an example. Its settings are concise and clear, but there are few functions! The WEB setting interface, as its name implies, uses a browser for connection settings! According to the default IP address of the manufacturer in the instruction. Enter 192.168.1.1 in the address bar of the browser and press enter to enter the settings page! If a connection fails, set the nic ip address to 192.168.1.X2-255). The network interface is displayed, prompt to add the account and password given by the manufacturer, and then confirm!

The above description has the same meaning for all ADSL Router installations, but may have different default IP addresses, accounts, and passwords according to the factory settings! After entering, the following interface will appear, but the interfaces made by various manufacturers are not the same. Some may even make more functions, but the main functions are similar! The default status is the top 1483 bridging mode, that is, the routing mode is not enabled! The following is the "2516PPPoE" mode. This is the virtual dialing routing mode! After selection, the following settings will add an "Account" and "password" input box!

Enter the account and password provided by China Telecom. The following DNS can be entered as the DNS of China Telecom! The value after "VPI" and "VCI" must be the same as that of China Telecom. You can ask China Telecom to give it to you! But most China Telecom uses the default value! After saving the settings, the routing is enabled, which is very simple. Other Cats may have different page designs, but the basic settings are the same! The following is a simple route setting for a fixed IP address. You only need to select the 1577 route mode or the 1483 route mode, and then the following setting box appears, in fact, some manufacturers do not see such numbers as 1577,1483 on the page, but simply write them as static IP addresses or wan ip addresses. These are fixed IP settings page!

VPI, VCI, Encapsulation Format needless to say, cannot be entered incorrectly! The following Wan IP address, mask, gateway, and DNS must be specified by China Telecom! After saving the settings, you can use the routing function. Below are the settings for the cat's Lan, which are generally available by default! As shown above, DHCP under the CAT's IP address is automatically assigned or manually assigned IP address mode selection, as well as the number of sub-hosts that can be supported! Because the routing function provided by the cat is relatively simple, generally there are not many sub-machines supported, generally around 30. For example, the maximum number of sub-machines for the cat is 20, more problems may occur, such as connection failure or serious packet loss. You can test the number of supported sub-hosts on your own!
◆ In "status monitoring", network connections and data transmission traffic accumulation are generally displayed! There are also functions such as displaying route tables!
◆ Enter the "account password" interface. The default account password set by the manufacturer can be changed. You can give it as needed!

Install the utstarcom adsl Router
◆ Set the nic ip address to 192.168.1.3 and subnet 255.255.0. Add 192.168.1.1 to the address bar of the browser, with the username admin and password utstar to go to the web page.
◆ Next is the "Lan" option, which does not need to be changed!
◆ The "Wan" option is followed, which is the focus of the modification! Enable the "atm vcc" option under "Wan,
◆ Point to add, the following interface appears, fill in VPI/VCI value, Note: If in the aal5-1 ~ There are VPI/VCI between aal5-4 and you are the same, you must change it to something else, you can add your !!
◆ Next, the "PPP" item of the "Wan", and delete the only protocol in it!
◆ In the "EOA" item of "Wan,
◆ Click "add", as shown in. The interface must be added in "atm vcc. Select the default route!
◆ Click "DNS" in "service" to add the DNS of China Telecom.

Do not forget. After completing each step, you must "Submit" and click "Submit" in "manage". After the submission is successful, click "Save and restart ", the rest do not need to be changed, and then the ADSL Router installation and sub-power-off will be restarted once, wait 5 ~ 6 minutes. All right. The route is successful. It can be found in 192.168.1.3 ~ You can access the Internet between 192.168.1.254 ~!!