Cisco Configuration switch Management address and default gateway

Configure the switch remote management address and default gateway

The topology diagram is as follows:

650) this.width=650; "Src=" Https://s1.51cto.com/oss/201710/29/1b8f7b6af37801733cf03704e748d09a.png-wh_500x0-wm_3 -wmp_4-s_475699717.png "title=" 57.png "alt=" 1b8f7b6af37801733cf03704e748d09a.png-wh_ "/>

1, Configuration PC0

650) this.width=650; "Src=" Https://s4.51cto.com/oss/201710/29/1040970991a285f60d06835e1725ca41.png-wh_500x0-wm_3 -wmp_4-s_2639041296.png "title=" 58.png "alt=" 1040970991a285f60d06835e1725ca41.png-wh_ "/>

2. Configuring the SW1 Switch

Switch (config) #no IP domain-lookup #关闭域名解析

Switch (config-line) #exec-timeout 0 0 #与交换机保持连接的时延, where the settings are always connected to the router, unless you logout

Switch (config-line) #logging syn #设置模式同步

Switch (config) #hostname SW1 #修改交换机的名称为SW1

SW1 (config) #line vty 0 4# into the virtual terminal

SW1 (config-line) #password ccna5188$ #设置telnet密码为ccna5188 $

SW1 (config-line) #login #敲该命令登陆下

SW1 (config) #enable secret [email protected] #设置特权模式的登陆密码 (ciphertext)

SW1 (config) #username ccna password ccna5188$ #设置本地用户ccna with a password of ccna5188$

SW1 (config) #line vty 0 4 #进入虚拟终端

SW1 (config-line) #login local #设置本地用户的telnet登陆

SW1 (config) #ip default-gateway 192.168.1.254 #设置该交换机的默认网关

SW1 (config) #int vlan1 #进入vlan1的端口

SW1 (config-if) #ip address 192.168.1.1 255.255.255.0 #配置交换机的管理地址为192.168.1.1 Subnet Mask is 255.255.255.0

SW1 (config-if) #no shutdown #启动这个vlan1

3. Configuring the R1 Router

Router (config) #hostname R1

R1 (config) #no IP domain-lo

R1 (config-line) #exec-timeout 0 0

R1 (config-line) #logging syn

R1 (config) #int fa0/0 #进入fa0/0 ports

R1 (config-if) #ip address 192.168.1.254 255.255.255.0 #配置fa0/0 with IPD addresses of 192.168.1.254, Subnet mask = 255.255.255.0

R1 (config-if) #no shutdown #打开端口

R1 (config-if) #no shutdown #进入fa0/1 ports

R1 (config-if) #ip address 192.168.2.254 255.255.255.0 #配置fa0/1 with IPD addresses of 192.168.2.254, Subnet mask = 255.255.255.0

R1 (config-if) #no shutdown #打开端口

4, Configuration PC1

650) this.width=650; "Src=" Https://s2.51cto.com/oss/201710/29/eef471ae6501b9a02c183e9077111b9f.png-wh_500x0-wm_3 -wmp_4-s_3256371882.png "title=" 59.png "alt=" Eef471ae6501b9a02c183e9077111b9f.png-wh_ "/>

5. View the status of the port on the router

R1#show IP int Brief

Interface ip-address OK? Method Status Protocol

fastethernet0/0 192.168.1.254 YES Manual up

FASTETHERNET0/1 192.168.2.254 YES Manual up

Vlan1 Unassigned YES unset administratively down

6, Test PC1 remote management SW1

650) this.width=650; "Src=" Https://s3.51cto.com/oss/201710/29/616eb0bda4a792731db2eb5ed8244f11.png-wh_500x0-wm_3 -wmp_4-s_1602804879.png "title=" 60.png "alt=" 616eb0bda4a792731db2eb5ed8244f11.png-wh_ "/>

This article is from the Server Ops blog, so be sure to keep this source http://shamereedwine.blog.51cto.com/5476890/1977267

Cisco Configuration switch Management address and default gateway