Cisco Wireless LAP1142 Upgrade

1. Pre-Preparation for upgrade LAP1142 :

because LAP1142 cannot obtain an IP address, the console line is connected to the AP , and an error is reported, the log is as follows :

*mar 1 00:00:44.491:%cdp_pd-2-power_low:all radios disabled-negotiatedws-c2960s-48lps-l (34bd.c8bc.5401)

*mar 1 00:00:50.422:%capwap-3-errorlog:not sending discovery request apdoes not having an Ip!!

*mar 1 00:01:00.422:%capwap-3-errorlog:not sending discovery request apdoes not having an Ip!!

2. determine If the AP itself has a problem, not the network cause the address cannot be obtained

2.1 specific practices are as follows :

find it first . Gateway and VLAN of the AP, looking all the way upstream switch connected to the AP to see if the DHCP configuration is correct (gateway, address range,VLAN and option 43 ) and other information

2.2 determine the network configuration is correct, put a PC into the VLAN of the AP, can correctly obtain the IP address of the VLAN where the corresponding AP resides

3.1 laps of the image file :

you can find the latest or most recent version from the official, note is the light system Image of the AP, it is best to find the official system version of the AP and WLC table to ensure compatibility

http://software.cisco.com/download/release.html?mdfid=282439881&flowid=6789&softwareid=280775090& Release=15.2.2-jb&relind=available&rellifecycle=ed&reltype=latest

650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/6B/6B/wKiom1Us0nLwGXpvAAHjTZTEedM550.jpg "title=" 1.png " alt= "Wkiom1us0nlwgxpvaahjtzteedm550.jpg"/>

3.2. ready to operate the documentation, as this is a local upgrade, the IP address of the PC needs to be configured to transmit the image files of the AP.

3.3 upgrade starts,the IP address in AP recovery mode is 10.0.0.1/8, and the local IP is 10.0.0.2/8.

placed in an address segment or a VLAN and shut down the local computer's computer firewall.

Open in The TFTP server is opened on the PC and the image file is placed in the TFTP specified directory

here is the C1140-k9w8-tar.124-23c.ja4.tar:

C1140-k9w8-tar.124-23c.ja4.tar----> C1140-k9w8-tar.default

Restart AP, and hold down the mode key :

Base Ethernet MACADDRESS:00:1D:A1:FF:3C:DC
Initializing Ethernet Port 0 ...
Reset Ethernet Port 0 ...
Reset done!
Ethernet link up, Mbps, Full-duplex
Ethernet Port 0 Initialized:link is up
button is pressed, Waitfor button to be released .. (You can loosenModekey)

Button pressed for seconds
Process_config_recovery:set IP address and config to default 10.0.0.1
Process_config_recovery:image Recovery
Image_recovery:download default IOS tar imageTftp://255.255.255.255/c1240-k9w7-tar.default(modified according to the actual situation)

the rest of the process isApthe process of reinstalling the system .

Upgrade Success Results :

AP Normal get address :

*mar 1 00:00:12.310:%SNMP-5-COLDSTART:SNMP agent on host ap6c20.569a.6e98is undergoing a cold start

*mar 1 00:12:39.044:%capwap-5-changed:capwap CHANGED State to DISCOVERY

*mar 1 00:12:39.111:%link-5-changed:interface dot11radio1, CHANGED State Toreset

*mar 1 00:12:39.112:%link-5-changed:interface dot11radio0, CHANGED State Toreset

*mar 1 00:12:40.298:%SSH-5-ENABLED:SSH 2.0 has been ENABLED

*mar 1 00:12:40.298:%lineproto-5-updown:line protocol on INTERFACEDOT11RADIO1, changed

*mar 1 00:12:40.298:%lineproto-5-updown:line protocol on Interfacedot11radio0, changed

*mar 1 00:12:49.108:%dhcp-6-address_assign:interface gigabitethernet0assigned DHCP ADDRESS 10.157.650) this.width=650 ; "Src=" Http://img.baidu.com/hi/face/i_f30.gif "alt=" I_f30.gif "/>.200, Mask 255.255.255.128, Hostnameap6c20.569a.6e98

AP Successful Discovery Controller:

*mar 1 00:13:02.501:%cdp_pd-4-power_ok:full power-negotiated inline Powersource

*mar 1 00:13:02.523:%link-3-updown:interface dot11radio1, changed state Toup

*mar 1 00:13:02.548:%link-3-updown:interface dot11radio0, changed state Toup

*mar 1 00:13:03.508:%lineproto-5-updown:line protocol on INTERFACEDOT11RADIO1, changed

*mar 1 00:13:03.509:%sys-6-logginghost_startstop:logging to host255.255.255.255 STARTED-CLI initiated

*mar 1 00:13:03.534:%lineproto-5-updown:line protocol on Interfacedot11radio0, changed

Translating "Cisco-capwap-controller" ... domain server (255.255.255.255)

*mar 1 00:13:08.897:%capwap-5-dhcp_option_43:controller address10.157.650) this.width=650; "src="/HTTP// Img.baidu.com/hi/face/i_f27.gif "alt=" I_f27.gif "/>.123 obtained through DHCP

AP Upgrade succeeded

This article is from "Dream Heart Dust" blog, please be sure to keep this source http://wangzhenqi.blog.51cto.com/1405949/1632355

Cisco Wireless LAP1142 upgrade