Cisco Packet Tracert Three-tier switch VLAN configuration

Lab Environment:

650) this.width=650; "alt=" Cisco Packet Tracert three-tier switch VLAN configuration-Ibm.chick-mingkang.zhou "src=" Http://img2.ph.126.net/2N Qfixjyba1gdiqtbuknhq==/6630601572768576164.png "style=" border:0px;height:auto;margin:0px 10px 0px 0px; "/>

Experimental Purpose:

1, the three layer switch divides three VLANs, is Vlan2\vnal3\vlan4, and the VLAN IP is set to: 192.168.2.1, 192.168.3.1, 192.168.4.1 respectively.

2, the FA0/1 port is set to trunk port, Fa0/4 joined VLAN4.

3, enable the routing function, to achieve interoperability between the VLANs.

4, set the two-layer switch, the FA0/1 port is set to trunk, and add FA0/2 join VLAN2,FA0/3 added VLAN3.

5, test the VLAN is connected.

Experimental steps:

1, the three layer switch divides three VLANs, is Vlan2\vnal3\vlan4, and the VLAN IP is set to: 192.168.2.1, 192.168.3.1, 192.168.4.1 respectively.

Switch>enable

Switch#conf T

Enter configuration commands, one per line. End with cntl/z.

Switch (config) #hostname coresw

Coresw (config) #vlan 2

CORESW (Config-vlan) #exit

Coresw (config) #vlan 3

CORESW (Config-vlan) #vlan 4

CORESW (Config-vlan) #

Coresw (config) #int VLAN 2

CORESW (config-if) #

%link-5-changed:interface Vlan2, CHANGED state-to-up

CORESW (config-if) #ip add 192.168.2.1 255.255.255.0

CORESW (config-if) #no shutdown

CORESW (config-if) #exit

Coresw (config) #int VLAN 3

CORESW (config-if) #

%link-5-changed:interface Vlan3, CHANGED state-to-up

CORESW (config-if) #ip add 192.168.3.1 255.255.255.0

CORESW (config-if) #no shutdown

CORESW (config-if) #exit

Coresw (config) #int VLAN 4

CORESW (config-if) #exit

%link-5-changed:interface Vlan4, CHANGED state-to-up

CORESW (config-if) #ip add 192.168.4.1 255.255.255.0

CORESW (config-if) #no shutdown

2, the FA0/1 port is set to trunk port, Fa0/4 joined VLAN4.

Coresw (config) #int FA0/1

CORESW (config-if) #switchport trunk Encapsulation dot1q

CORESW (config-if) #switchport mode trunk

Coresw (config) #int FA0/4

CORESW (config-if) #switchport mode access

CORESW (config-if) #switchport Access VLAN 4

3, enable the routing function, to achieve interoperability between the VLANs.

Coresw#conf T

Enter configuration commands, one per line. End with cntl/z.

Coresw (config) #ip routing

Coresw (config) #router rip

CORESW (config-router) #ver 2

CORESW (config-router) #no au

CORESW (config-router) #net 192.168.2.0

CORESW (config-router) #net 192.168.3.0

CORESW (config-router) #net 192.168.4.0

4, set the two-layer switch partition VLAN2/VLAN3, the FA0/1 port is set to trunk, and FA0/2 added VLAN2,FA0/3 added VLAN3.

Switch>enable

Switch#conf T

Enter configuration commands, one per line. End with cntl/z.

Switch (config) #vlan 2

Switch (Config-vlan) #exit

Switch (config) #vlan 3

Switch (Config-vlan) #exit

Switch (config) #

Switch (config) #int FA0/1

Switch (config-if) #switchport mode trunk

5, test the VLAN is connected.

650) this.width=650; "alt=" Cisco Packet Tracert three-tier switch VLAN configuration-Ibm.chick-mingkang.zhou "src=" Http://img2.ph.126.net/LP Rsjuool21jadaugxblpw==/3355181722493036123.jpg "style=" border:0px;height:auto;margin:0px 10px 0px 0px; "/>

This article is from the "Learning Journey" blog, so be sure to keep this source http://mingkang.blog.51cto.com/9678221/1617702

Cisco Packet Tracert Three-tier switch VLAN configuration