First, this is ready to upgrade the equipment model AIR-CAP16021-C-K9
Second, set the IP address of the computer and ready TFTP: Set the computer IP to 10.0.0.2/8,tftp server is using SolarWinds 10.9.1.33.
Third, connect the console line to view the port of the console line
Four, use set serial port parameters as follows
Download 1602I of the FAT ap iOS file, url: http://down.51cto.com/data/1897579
My AP uses iOS is downloaded in 51CTO, other models of AP please download the corresponding iOS file
Six, modify the image file suffix is default, and placed in the TFTP root directory (key steps)
The name of the image file must be this: Ap1g2-k9w7-tar.default, if not the file name, will be an error as follows:
%error opening tftp://255.255.255.255/ap1g2-k9w7-tar.default (no such file or directory) APS:
The IP address must be set on this segment of 10.0.0.0/8 because the IP address used by the default AP upgrade is 10.0.0.1
Seven, in the case of power down the reset key, plug in power, press and hold reset for about 20 seconds, after the following prompt, you can release, then, the AP will automatically upgrade
IOS bootloader-starting System.
FLASH Chip:micron n25q256
Xmodem file system is available.
Flashfs[0]: Files, 9 directories
Flashfs[0]: 0 Orphaned files, 0 orphaned directories
FLASHFS[0]: Total bytes:31936000
Flashfs[0]: Bytes used:16559616
Flashfs[0]: Bytes available:15376384
Flashfs[0]: Flashfs fsck took seconds.
Reading Cookie from Seeprom
Base Ethernet MAC Address:18:e7:28:1a:2a:c7
Loopback_mode = 0
button is pressed, and wait for button to be released ...
Button pressed for seconds
Process_config_recovery:set IP address and config to default 10.0.0.1
Process_config_recovery:image Recovery
Image_recovery:download default IOS tar image Tftp://255.255.255.255/ap1g2-k9w7-tar.default
Examining Image ...
Extracting info (288 bytes)
Image Info:
Version Suffix:k9w7-.153-3.jab
Image Name:ap1g2-k9w7-mx.153-3.jab
Version Directory:ap1g2-k9w7-mx.153-3.jab
Ios Image size:1290752
Total Image size:11387392
Image feature:wireless lan| LWAPP
Image family:ap1g2
Wireless Switch Management version:8.0.72.236
Eight, after about five minutes of the brush process, you can enter the system
*mar 1 00:00:38.027:%sys-5-restart:system restarted--
Cisco IOS Software, C1600 Software (ap1g2-k9w7-m), Version 15.3 (3) JAB, RELEASE Software (FC1)
Technical Support:http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 02-sep-14 20:36 by Prod_rel_team
*mar 1 00:00:38.027:%SNMP-5-COLDSTART:SNMP agent on host AP is undergoing a cold start
*mar 1 00:00:38.955:%lineproto-5-updown:line protocol on Interface BVI1, changed
*mar 1 00:00:38.959:%lineproto-5-updown:line protocol on Interface Dot11radio0, changed
*mar 1 00:00:38.959:%lineproto-5-updown:line protocol on Interface Dot11radio1, changed
Ap>
Ix. Entry System
Ap> en
Enter the password Cisco
Ten, the next can be configured, we can configure the management address of the AP under the CLI, and then turn on HTTP management.
XI. configuration process (slightly)
12. Backup configuration file copy flash:/config.txt tftp://192.168.58.158 Backup is complete and duly completed.
Cisco wireless AP Brush for FAT AP