Computer Boot BIOS language meaning

When a problem occurs in a computer post, there are a variety of English phrases, which contain very important information, which can be used to solve some small problems, but these English baffled some of the friends, the following is some common BIOS interpretation, you can refer to.

1.CMOS Battery failed

Chinese: CMOS battery failure.

Explanation: This shows that the CMOS battery is running out of power, just replace the new battery.

2.CMOS Check sum error-defaults loaded

CMOS to perform all the checks found errors, to load system defaults.

Explanation: In general, this statement is that the battery is running out of power, you can change the battery to try, if the problem is not resolved, then that the CMOS ram may have problems, if not a year to the dealer place to change a motherboard, after a year to let the dealer back to the manufacturer to repair it!

3.Press ESC to skip memory test

Chinese: Memory check is in progress, you can press ESC to skip.

Explanation: This is because there is no skip memory in the CMOS 第二、三、四次 test, the boot will perform four memory test, of course, you can also press ESC key to end the memory check, but every time this is too troublesome, you can enter the COMs settings after the BIOS featurs setup, Set the quick power on Self test to Enabled and restart after storage.

4.Keyboard error or no keyboard present

Chinese: Keyboard error or keyboard not connected.

Explanation: Check if the keyboard connection is loose or damaged.

5.Hard Disk Install failure

Chinese: Hard drive installation failed.

Explanation: This is because the power cable or data cable for the hard drive may not be plugged in or the hard disk jumper is set incorrectly. You can check the root of the hard drive is plugged in, to see the same data line on the two hard disk jumper settings are the same, if the same, as long as the two hard drive jumper set to the same (one set to master, the other set to slave).

6.Secondary slave Hard Fail

Chinese: Failed to detect from disk

Explanation: May be the CMOS settings, such as not from the disk but set in the CMOS from the disk, then there will be errors, then you can enter the COMs settings select IDE HDD auto detection for hard drive automatic detection. It may also be the hard drive's power cable, the data cable may not be connected or the hard disk jumper settings, the solution to refer to the 5th.

7.Floppy disk (s) fail or floppy disk (s) fail (80) or floppy disk (s) fail (40)

Chinese: Unable to drive floppy drive.

Explanation: The system prompts to find the floppy drive, to see whether the floppy drive power cord and data cable is loose or wrong, or the floppy drive to another machine to try, if these are not, then have to buy another, fortunately the floppy drive is not expensive.

8.Hard disk (s) diagnosis fail

Chinese: An error occurred while performing a hard drive diagnostics.

Explanation: This problem generally means that the hard disk itself has failed, you can put the hard drive on another machine to try, if the problem is not resolved, can only go to repair.

9.Memory Test fail

Chinese: Memory detection failed.

Explanation: Reseat the memory bar to see if it can be resolved, this problem is generally because the memory is incompatible with each other, to change a bar!

10.Override Enable-defaults Loaded

The current CMOS settings cannot boot the system, loading the preset in the BIOS to boot the system.

Explanation: Generally is in the COMs within the setting error, as long as enter the COMs settings select Load Setup defaults load the original set value and then restart.

11.Press TAB to show POST screen

Chinese: Press the TAB key to toggle the screen display.

Explanation: Some OEM manufacturers will use their own design display screen to replace the BIOS preset boot display screen, we can press the TAB key to the BIOS preset boot screen and the manufacturer's custom screen to switch between.

12.Resuming from Disk,press TAB to show POST screen

Chinese: Boot from hard drive, press TAB to show post screen.

Explanation: This is because some motherboard BIOS provides the suspend to disk (the hard drive hangs) the function, if we use suspend to disk the way to shut down, then we will display this prompt message when the next boot.

13.Hareware Monitor found an error,enter power MANAGEMENT setup for details,press F1 to Continue,del to enter SETUP

Chinese: monitoring function found error, enter the power MANAGEMENT Setup to see the details, press F1 key to continue the boot process, press del key to enter COMs settings.

Explanation: Some motherboards have the hardware monitoring function, you can set the motherboard and CPU temperature monitoring, voltage regulator voltage output and monitor the speed of each fan, when the monitoring function in the boot found abnormal conditions, then the above paragraph will appear, then you can enter the COMs settings select Power MANAGEMENT SETUP, on the right side of the **fan monitor**, **thermal monitor** and **voltage to see which part of the abnormal issue, and then resolved.