Install the Linux tutorials and connect remotely using putty

安装Linux教程和使用putty进行远程连接

To create a new virtual machine using Vmwareworkstationpro:

Click on "Create a new virtual machine" to enter the following screen, select a custom can:

Just click on the next step:

You will then go to the following interface (you can directly select the Setup CD image file, which is installed later, first create a blank hard disk with the virtual machine):

Since this is the installation of Linux systems, choose Linux (L)
Version Select Red Hat Linux 6, as this is a Linux operating system for enterprise users

Next, create the virtual machine name (first name customization can)

Next set up the processor configuration, its total processing core number can not exceed 8 (my own process is 8), single core can:

Virtual memory is 1.5 times times-twice times the physical memory:

Bridging networks: Virtual machines in two hosts communicate with each other
NAT Address Translation: Host Internet while virtual machine can also surf the Internet, host and virtual machine share the same IP
Host mode: Limited to communication between multiple virtual machines on the host computer
This experiment uses the host mode to:

I/O Controller type selection recommended:

Disk type selection recommended:

Select "Create a new Vdisk" to:

Maximum disk size is 40GB
Select "Split disk into multiple files" for ease of migration:

Save the file in the newly created folder and delete it later (delete the folder)

After you create the virtual machine, look at the hardware, where the sound card and the printer do not need to remove them:

The following interface appears, indicating that the virtual machine has been generated and then goes to edit virtual machine settings:

Next we can install the image file:

After entering the browsing interface, find the location where you will mirror Red hat and I put it on the desktop:

After the mirror is installed, you can turn on the virtual machine:

After installing the virtual machine, you will see the following interface, click Skip:

When you go in, you'll see the following screen:

Select the Chinese version (English version is also available):

Choose US English style:

Go to the following screen and select "Ignore All data":

Select basic storage device, which is the hard drive:

The next step is to define the host name and customize it:

The default time zone can:
!

Next enter the password, note here is the Administrator password:

Next, use the custom layout:

Next to Partition:

First to the root directory partition:

Next to the kernel partition:

Next is swap (swap file system), virtual memory, which is added to the file system type:

/home Represents the user's family partition and has no effect on allocating space to the home partition:

After the distinction is finished, the following interface will appear:

Then jump out of the screen below and click "Format" to:

Then select "Write Modifications to disk":

The interface is entered after the partition is finished, which means the system is installed in the SDA2:

After installation will appear the following interface, at this time, if a Linux beginner, you can first put it on the desktop, it is more convenient to use:

The interface indicates that your Linux installation is complete and you need to reboot:

After rebooting, you will go to the following screen and click Forward:

By agreeing to this license, you can:

Select "Register Later" to:

Do not update, click Forward directly:

Next create the user, which can be created or not created, if not created, there is currently only one root

Next set the time, we can manually set:

Then reboot the system:

After restarting, you will be entered into the login screen (enter your username and password):


Next, you will get to the main interface:

You can then set the desktop to adjust the display resolution:


After the installation of Linux, you can communicate with the host, but to communicate with the host, it is necessary to set up a network card, the first remote connection, right-click the interface, click on the "Open in Terminal":

Then the following code appears (after ifconfig if nothing is followed to see all the network card, if followed by eth0 is to see only the eth0 this network card):

Because the eth0 does not have an IP address in it, the network card must be configured:

After editing the NIC, the following interface appears:

Then enter a for editing
Onboot=yes indicates that the network adapter is switched on and the bootproto=static is fixed IP value:

Then enter the IP address, and the subnet mask also has the gateway:

Then press the ESC key to exit the input mode, then press: The cursor automatically enters the last line, at this time enter WQ
Save, note that Wq must be lowercase:

Then enter the service network restart command restart:

The IP address can be re-viewed after a reboot (that is, the IP address is well-equipped)

Then go to Control Panel-Network Sharing Center-Change adapter settings-vmnet1 to set the IP address (the IP address should be in the same network segment as the virtual machine's IP address):

Right-click the Vmnet1 property and the following interface appears:

Then set the IP address, subnet mask:

Then confirm that the host IP address is already well-equipped.
Then enter the command prompt on the desktop:

Then use their own host to ping the virtual machine's IP address, the interface indicates that it has been ping:

Host ping can be used putty (Baidu download can) to remote connection
Putty in hostname is the IP address set by the preceding virtual machine:

After connecting, enter the user name and password that you just logged in to the interface:

Here, the entire Linux installation is complete and the remote connection is OK.
V

Install the Linux tutorials and connect remotely using putty