Photoshop colorful and gaudy glow effect production tutorial

To the users of Photoshop software to share the colorful glow of the production of the effect of the tutorial.

Tutorial Sharing:

1. Open the picture of the material, create the optional Color adjustment layer, adjust the green, the parameters and effect as shown below. This step darkens the green in the picture.

< map 1>

< map 2>

2, press CTRL + J to copy the current optional color adjustment layer, the effect of the following figure.

< map 3>

3, the creation of optional color adjustment layer, yellow, green, white, black to adjust, parameter settings such as Figure 4-7, the effect is shown in Figure 8. This step mainly turns the yellow-green in the picture to orange-yellow, the high light area increases the light blue.

< map 4>

< map 5>

< map 6>

< map 7>

< map 8>

4, press CTRL + ALT + 2 to bring up the high light selection, press CTRL + Shift + I to select the dark selection, and then create a curve adjustment layer, RGB, green, blue channel adjustment, parameter settings such as Figure 9, the effect is as Figure 10. This step darkens the dark part of the picture and adds Blue.

< map 9>

< map 10>

5, press CTRL + J to copy the current curve adjustment layer, and press CTRL + ALT + G to create a clipping mask, the effect of the following figure.

< map 11>

6, create a color balance adjustment layer, the shadow, highlight adjustment, parameter settings such as Figure 12,13, after the creation of a clipping mask, the effect is shown in Figure 14. This step adds blue to the dark part.

< map 12>

< map 13>

< map 14>

7, create an optional color adjustment layer, the yellow adjustment, parameter settings such as Figure 15, determined to create a clipping mask, the effect is shown in Figure 16. This step adds orange red to the dark part.

< map 15>

< map 16>

8, create brightness/Contrast adjustment layer, greatly increase the brightness and contrast, parameter settings such as Figure 17, after the creation of a clipping mask, and then the mask filled with black, with a low transparency soft edge white brush to wipe out the area shown in Figure 18. This step increases the local brightness of the dark part.

< map 17>

< map 18>

9, create a new layer, creating a clipping mask, using the Lasso tool to check out the selection shown in the following figure, feather 35 pixels after the fill orange: #F7A238, remove the selection after the blending mode to "soft light", the effect of the following figure. This step adds a warm color to the dark part.

< map 19>

10, now to deal with the sky part. Copy the background layer one layer, press CTRL + Shift +] top, as shown below.

< map 20>

11. Enter the channel panel, copy the blue channel and get the blue copy channel. Press CTRL + M to adjust the curve of the blue copy channel, darken The dark, highlight the area, the effect is as follows.

< map 21>

12, set the foreground color to black, and then use the brush to paint the area outside the sky black, as shown below.

< map 22>

13, hold down CTRL + the left mouse button click on the channel panel blue copy channel thumbnail load selection; point RGB channel return to the Layers panel. Create a new layer, fill the white with the paint bucket tool, hide the background copy layer after canceling the selection, and the effect is shown below.

< map 23>

14, open the sky material large map, with the move tool dragged in, create a clipping mask after adjusting the position, the effect of the following figure.

< map 24>

15, select the menu: Filter > Blur > Gaussian blur, the value is 5, determine the effect of the following figure.

< map 25>

16, create curve adjustment layer, the RGB, red, green, blue channel adjustment, parameter settings such as Figure 26, determined after the creation of a clipping mask, the effect is shown in Figure 27. This step darkens the sky slightly and reduces the dark red.

< map 26>

< map 27>

17, press CTRL + J to copy the current curve adjustment layer, create a clipping mask after the effect of the following figure.

< map 28>

18, create a solid color adjustment layer, the color is set to dark blue: #0C3148, make sure that the mask filled with black, and then use the transparency of the lower soft edge white brush to darken the top and bottom area, the effect of the following figure.

< map 29>

19. Create a new layer, use the elliptical marquee tool to pull out the selection shown in the following figure, feather 30 pixels and fill with orange yellow: #F7A238, remove the selection after the blending mode to "overlay", the effect of the following figure.

< map 30>

20, press CTRL + J to copy the current layer, blending mode to "soft light", the effect of the following figure.

< map 31>

21, the background layer to copy a layer, press CTRL + Shift +] top, with the pen tool to pull out the characters, into the selection after adding layer mask, the following figure.

< map 32>

22, create curve adjustment layer, the RGB channel adjustment, parameter settings such as Figure 33, determined after the creation of clipping masks, the effect is shown in Figure 34. This step darkens the character part.

< map 33>

< map 34>

23, create an optional color adjustment layer, adjust the white, parameter settings such as Figure 35, after the creation of a clipping mask, the effect is shown in Figure 36. This step adds a light cyan to the character's high light area.

< map 35>

< map 36>

24, create curve adjustment layer, the RGB, red, green channel adjustment, parameter settings such as Figure 37, determine after the creation of clipping masks, and then the mask filled with black, and then use the transparency of the lower soft edge white brush to the character backlight area, as shown in Figure 38.

< map 37>

< map 38>

25, create a new layer, creating a clipping mask, with a transparent lower soft edge brush to the left side of the character to the edge of the light painted pale yellow, the following figure.

< map 39>

26, create curve adjustment layer, the RGB, blue channel adjustment, parameter settings such as Figure 40, after the mask filled with black, and then with the transparency of the lower soft edge white brush to the right and the bottom of the area painted darker, the effect is shown in Figure 41. This step adds a dark angle to the picture.

< map 40>

< map 41>

27. Create a new layer, use the elliptical marquee tool to pull out the selection shown in the following figure, feather 25 pixels and fill orange and yellow: #F7A238, remove the selection and change the blending mode to "color filter", the effect is as follows.

< map 42>

28, create a new layer, with the elliptical marquee tool pull out the selection shown in the following figure, feather 20 pixels after the fill of light yellow, remove the selection after the blending mode to "filter", and then appropriately reduce the opacity of the layer, the effect of the following figure. These steps give the picture an orange-yellow high light.

< map 43>

29, CTRL + ALT + 2 up the high light selection, and then create curve adjustment layer, RGB, blue channel adjustment, parameter settings such as Figure 44, the effect is as figure 45. This step darkens the high light area a little bit.

< map 44>

< map 45>

Finally, strengthen the local light and finish the final effect.

Well, the above information is small to give you photoshop this software users bring the color of the gaudy glow effect of the production of the full content of the tutorial, you see the users of Photoshop software here, now you are very clear about it, So now go to the small series to share their own to make a beautiful picture.