To the users of Photoshop software for detailed analysis to share a picture of dark blue and add the glow effect of the production tutorial.
1, open the original material large map, create hue/saturation adjustment layer, the whole map, red, yellow, green adjustment, parameter settings such as Figure 1-4, the effect is shown in Figure 5. This step quickly reduces the primary color saturation and gets the neutral picture.
2, create curve adjustment layer, RGB, green, blue channel adjustment, parameter settings such as Figure 6-8, the effect is shown in Figure 9. This step increases the shade contrast of the picture and adds Blue purple to the dark part.
3, press CTRL + ALT + 2 to bring up the high light selection, press CTRL + Shift + I to select the dark selection, and then create a curve adjustment layer, RGB, red, green, blue channel adjustment, parameter settings such as Figure 10-13, the effect is as Figure 14. This step darkens the dark part and reduces the red and increases the blue.
4, press CTRL + J to copy the current curve adjustment layer, press CTRL + ALT + G to create a clipping mask, the effect of the following figure.
5, create a color balance adjustment layer, the shadow adjustment, parameter settings such as Figure 16, after the creation of a clipping mask, the effect is shown in Figure 17. This step adds blue to the dark part of the picture.
6, create brightness/Contrast adjustment layer, the appropriate increase in contrast, parameter settings such as Figure 18, determine after the creation of a clipping mask, and then the mask filled with black, with the Lasso tool to check out the selection shown in Figure 19, feather 65 pixels after filling white. This step increases the image contrast of the light source area.
7, CTRL + ALT + 2 up the high light selection, and then create a curve adjustment layer, RGB, red, green, blue channel adjustment, parameter settings such as Figure 20-23, the effect is as Figure 24. This step lightens the highlight area slightly and adds blue-red.
8, create a solid color adjustment layer, color set to orange red: #CC8A74, after the creation of a clipping mask, then the mask filled with black, with a soft white brush to the bottom of the selection section, and then change the blending mode to "color deepen", the opacity to: 30%. The effect is shown below. This step adds warm colors to the high light area.
9, create curve adjustment layer, the highlights of the highlight area, parameter settings such as Figure 26, determine after the creation of a clipping mask, and then fill the mask black, and then use the soft side of the white brush to the bottom area need to lighten the area, such as Figure 27.
10, press CTRL + ALT + 2 to bring up the high light selection, and then create a solid color adjustment layer, the color is set to light red: #FBD9C6, determine the opacity after the change to: 30%. Add a layer mask, with a soft black brush to the characters and do not need to increase the warm color of the parts, the effect of the following figure.
11, create a new layer, with a lower transparency of the soft side of the black brush to the left and right side of the forest light light part of the color darker, the effect of the following figure.
12. Create a new layer, use the elliptical marquee tool to pull out the selection shown in the following figure, feather 45 pixels and fill with orange: #CC8A74, after the selection is canceled, the blending mode is changed to "overlay", and the effect is shown below.
13, press CTRL + J to copy the current layer layer, the effect of the following figure.
14, press CTRL + J to copy the current layer, blending mode to "soft light", the effect of the following figure.
15, press CTRL + J to copy the current layer layer, the opacity to: 50%, the effect of the following figure.
16, press CTRL + J to copy the current layer, blending mode to "filter Color", the opacity to: 100%, the effect of the following figure.
17, press CTRL + J to copy the current layer, press CTRL + T a little smaller, the effect of the following figure. These steps add warm and high light to the picture.
18, create curve adjustment layer, the RGB, blue channel adjustment, parameter settings, such as Figure 36, after the mask to fill the black, and then use the soft side of the black brush to paint the corner area, the effect is shown in Figure 37. This step adds a dark angle to the picture.
19, create an optional color adjustment layer, the blue, neutral, black adjustment, parameter settings such as Figure 38-40, the effect is shown in Figure 41. This step is to fine-tune the cool colors in the picture.
20, the background layer to copy a layer, press CTRL + Shift +] top, with the pen tool to pull out the characters, into the selection after adding layer mask, the effect of the following figure.
21, create curve adjustment layer, the RGB, green, blue channel adjustment, parameter settings such as Figure 43, after the creation of a clipping mask, the effect is shown in Figure 44. This step darkens the character part and adds Blue.
22. Use Lasso tool to check out the selection shown in Figure 46, feather 15 pixel after creating curve adjustment layer, the RGB channel down a little, parameter settings such as Figure 45, determine after the creation of a clipping mask, the effect is as Figure 46. This step darkens the backlight area of the character.
23, strengthen the character part of the light area of the brightness, and the bottom area darkened a little, the effect of the following figure.
24, the top of the area to add a bit of dark, arbitrary method, the effect of the following figure.
25, create a new layer, press CTRL + ALT + Shift + E-stamped layer. Select menu: Filter > Blur > Motion blur, Angle set to 45 degrees, distance set to 150, after the blending mode is changed to "soft light", the opacity to: 30%, the effect of the following figure. This step of the picture to soften processing.
Finally, rub the skin of the character, fine-tune the overall color, complete the final effect.
Okay, the above information is small compiled to you photoshop this software users brought to the detailed picture of dark blue and add the effect of the production of a tutorial to share the full content, you see the users here to believe that you are now very clear method of it, So now you go to the small part of the way to share the method to try the effect of it.
