For the users of Photoshop software, share a tutorial on the neutral color effect of the grayed out.
1, open the original material large map, create hue/saturation adjustment layer, the whole map, red, yellow, green, cyan adjustment, parameter settings such as Figure 1-5, the effect is as Figure 6. This step quickly turns the background primary color into a neutral color.
2, press CTRL + J to copy the current hue/saturation adjustment layer, the effect of the following figure.
3, and then press CTRL + J the current hue/Saturation adjustment layer Copy layer, the opacity to: 30%, the effect of the following figure.
4, CTRL + ALT + 2 up the high light selection, and then create a curve adjustment layer, RGB, blue channel adjustment, parameter settings such as Figure 9,10, the effect is shown in Figure 11. This step increases the brightness of the picture's highlight area and adds Blue.
5, the creation of optional color adjustment layer, red, yellow, white, black to adjust, parameter settings such as Figure 12-15, the effect is shown in Figure 16. This step is to fine-tune the warm colors in the picture and to add a light blue color to the high lighting area, and the dark part to increase the blue purple.
6, press CTRL + J to copy the current optional color adjustment layer, the opacity to: 50%, the effect of the following figure.
7, press CTRL + ALT + 2 to bring up the high light selection, press CTRL + Shift + I to select the dark selection, and then create a curve adjustment layer, RGB, red, green, blue channel adjustment, parameter settings such as Figure 18-21, the effect is as Figure 22. This step increases the dark part of the picture by contrast, and increases the cool color.
8, press CTRL + J to copy the current curve adjustment layer, press CTRL + ALT + G to create a clipping mask, the effect of the following figure.
9, create a new layer, press the letter key "D" before, the background color reverts to the default black and white, then selects the menu: Filter > Render > Cloud, determines the blending mode to "color filter", presses ALT key to add the layer mask, and erases the upper right corner area with the lower transparent soft edge white brush, the following figure.
10, press CTRL + J to copy the current layer layer, the mask filled with black, and then with a low transparency soft white brush to the upper right corner area, the effect of the following figure. These two steps add a lighter smoke effect to the right side of the picture.
11, create a color balance adjustment layer, adjust the high light, parameter settings such as Figure 26, after the mask to fill the black, and then with the transparency of the lower soft white brush to the upper right corner area, the effect is shown in Figure 27.
12, the background layer to copy a layer, with the pen tool to the characters face and skin part of the cut out, into the selection after adding layer mask, and then the layer opacity to: 65%, the effect of the following figure.
13, create curve adjustment layer, the RGB channel down a bit, parameter settings such as Figure 29, determine after the creation of a clipping mask, and then the mask filled with black, with a lower level of transparency of the soft white brush the character backlight area painted darker, the effect is shown in Figure 30.
14, create curve adjustment layer, the RGB channel down, parameter settings such as Figure 31, to determine the mask filled with black, and then the soft side of the white brush to the bottom and the left side of the area painted darker, the effect is shown in Figure 32. This step adds a dark angle to the picture.
15, press CTRL + J the current curve adjustment layer copy one layer, the opacity to: 50%, the effect of the following figure.
16. Create a new layer, press CTRL + ALT + Shift + E-stamp layer, and blur the next figure selection with the Blur tool.
17, a new layer, stamped layer, select menu: Filter > Blur > Dynamic blur, Angle set to 45 degrees, the distance is set to 150, to determine the blending mode to "soft light", the opacity to: 50%, the effect of the following figure. This step of the picture to soften processing.
18, a new layer, stamped layer, blending mode to "filter", hold down the ALT key to add a layer mask, with a lower transparency of the soft white brush to the right side of the light on the area, the effect of the following figure.
19, create curve adjustment layer, the RGB channel down a bit, parameter settings such as Figure 37, after the mask to fill the black, and then use the soft side of the white brush to darken the area, as shown in Figure 38.
Finally, rub the skin of the character, strengthen the local light and finish the final effect.
Well, the above information is small compiled to you photoshop this software users brought to the details of the neutral color effect of the gray to share the full content of the tutorial, you see the users of Photoshop software here, I'm sure you're clear about the tutorial now. , then quickly go to the small part of the share of their own to try to color it.
