To give you Photoshop software users to detailed analysis to share the production of super bright spot text effect of the tutorial.
1. New layer w:42.5cm, h:59.4cm,300 Dpi,cmyk.
Draw a heart shape quickly with a paintbrush.
2. Draw a sketch of the text, considering just a sketch, if you feel more comfortable on paper, you can draw and then scan to the computer Oh ~
3. This one is very simple, use pen tool to hook up the words that you draw ~
(The original tutorial to be implemented in the AI, small series adapted a bit ~ Anyway can make, is kingly, wow Card card)
Second, the production of more lines
1. In the path channel to save the pen just sketched out the path.
2. Set brush, soft edge, 10 pixel, opacity 100%. Back to the pen tool, for strokes, no simulation pressure.
3. Filters > Blur > Motion blur, 60°, size 20. Let's click OK.
4. Change the transparency to about 50% ~ Add mask, then hide part with black brush.
5. In the path layer, find the path you saved before, with the pen tool to adjust slightly, the approximate shape as shown in the following picture Oh ~
6. or stroke 10px. In order to make the word more realistic, we have to stroke the next 5px, 10px, 15px, remember to adjust the transparency, transparency is also different ~ effect See the 7th step in the diagram.
7. Add masks and hide the ends of these lines with a black brush.
8. On the basis of the original word line, to increase the thickness of the line at both ends of the fine, the effect shown in the following figure.
9. Draw another one and try to thicken the left side of each letter. Because this can leave word and word spacing between the Oh ~
10. Remember to let each line fade out, otherwise it is not true ~
11. The result is the image below
1. Now we're going to create a gradient map adjustment layer for all the layers (Layers > New adjustment layer > Gradient map)
Color: #000000, #54000c, #d69f0a, #fffee9.
2. Let the gradient map adjustment layer always stay at the top. Now that we have finished the line, it's time for us to add special effects to it, that is, heightening the light!
Repeat the previous path, but this time it is 100-200px and then simulate the pressure. Uses a 50% gray (#8c8c8c).
Layer Blending mode-color filter.
3. Add a high light to all the thickened parts of the text
4. Now with white to add more thicker lines, but no simulation pressure Oh ~ line is probably between the 25-75px.
5. The soft white lines surround the text, making it look more thick.
To increase the light effect of the text
Use flare image footage and place it into PS. Change the angle of light, 90°. Layer Blending mode-color filter
2. Copy the light effect, then change the size, w:200%, h:200%, Angle: 40°.
3. Second light effect, filter > Blur > Gaussian blur. About 30px.
4. Set up two light groups and then copy them, respectively, in the position shown in the following figure.
5. After the text, also repeat the above (three to four steps), the effect shown in the following figure.
6. In the same way, add some lines around the text.
1. Open the "blurry lighte image" material, put it in, set to filter color.
2. Add mask, wipe, the effect shown in the following figure.
Six, the Light enhancement
Come on, let's increase the contrast of the light to make the effect cool.
1. Add a black and white gradient mapping adjustment layer, set to clip mask.
Sets its layer style to overlay.
2. Copy the spot and place it in a different position in the diagram.
3. Copy some ~ change its size, then put it in the place you want to place ~ Don't let it too big ~
4. Now we combine the base brush. Brush settings-Brush tip shape-size 50px-hardness 80%-spacing 150%
5. Open shape dynamics, scatter 550.
6. Turn on the transfer and change the settings.
7. Draw more lines around the text with a brush (the place where the circle is shown in the picture)
Seven, increase the noise point
1. Now we increase the noise without destroying the color and the light effect.
Select 50% Gray (#8c8c8c), new layer, fill.
Appears Brown because it is the following gradient map layer
2. Filters > Noise > Add Noise, and then enter a maximum value of 400%
3. blur it with 0.8 pixels (Filter > Blur > Gaussian blur).
4. Change layer mode-brightness, transparency 5%.
5. Make final adjustments, Layer > New Adjust layer > photo filter. Select Red. Wow, that's it!
Okay, the above information is small make up to you photoshop this software users to bring the detailed production of super bright spot text effect of the tutorial to share the full content of the whole, you see the users here, now you are very clear the production method of it, Then you will follow the small series of the tutorial to make their own.
