Print Server FAQ

Centralized problem of ST-P101 single parallel port 10 MB printing server

Q: Why is a write error always prompted when I cannot find or set an IP address during installation of my printing server?

A: The solution is to add a netbeui Protocol and A Netlink Protocol group to the Protocol of the local Nic. restart the computer to solve the problem.

Q: Why can't I PING the IP address of the print server?

A: P101 print the server's IP address. The factory IP address is 10.0.0.1 subnet mask 255.255.255.0. The gateway does not have
Set the IP address of the computer to 10.0.0. *.

Q: The IP address of our LAN is automatically obtained, but after the printing server is connected, several computers will not be able to access the Internet. After checking the IP address, it will be allocated to the IP address segment 10.0.0?

A: Enter the print server configuration program PrintServerConfiguration and select DHCP Cfg to Disable the DHCP function and select (Disable ).

(2) ST-P102.ST-P101U.ST-P103.ST-P103U printing server concentration problem

Q: Why can't I find the printer server through PSadmin in my XP or 2000 system?

A: Due to version 2000, the compatibility of some low-layer protocols is not very good. The solution is to add A Netlink protocol group to the NIC protocol and reconnect it. after finding it, set a fixed IP address for the printer server (it is best not to obtain it automatically). This protocol can be deleted after the printer is added and the test page is successfully displayed.

Q: My printing server cannot access the Web management interface?

A: First, make sure that the IP address of the printing server and the IP address of the computer are in the same network segment. The printing server can be found, and then enter the IP address of the printing server in IE to log on.

Q: How can I restore the factory value of a printing server?

A: Go to the Web Management page of the printing server and click LodaingFctory In the last LodaingFctory to restore the factory settings.

Q: Why is it best not to obtain the IP address of my printing server automatically?

A: due to the complexity of some local network environments (VPN, network isolation, VLAN, etc) it is best to specify the IP address of the same network segment as the computer and make sure that the IP address can be allocated to the router (ping)

(3) New Fei Xun printing server Series

Installation of NPS-301U 301WU 300U 300WU and other models on HP1000 Series

Q: Why is an error in printer printing correct?

A: Right-click the print icon you added and choose Properties> port. You need to remove the two-way enable support hook.

Q: I added a printer and deleted it before adding it, but the port is occupied?

A: This is because the port used by the original printer is not deleted, choose "Control Panel"> "Printer"> "right-click a blank area"> "server properties"> "Port"> "select the printer port you added"> "delete port". If the port cannot be deleted, restart the computer, the order of deletion is to delete the printer icon and then the port.

Q: Are there many computers in my LAN easy to add?

A: For Client installation, you can add A network printer port to the client when there are many customers. You do not need to add A local printer to each computer, but the printer driver must be installed on each computer, when HP1000 HP1020 and other models are used, PSMonter must be installed on each computer, the network environment is complex-the printing speed is slower than that of the local printer and other problems may occur.

Q: The printing server can be played within 1st days. It cannot be printed on 2nd servers.

A: This is because HP1000, 1020,1010 and other special models need to rely on the self-check process during the printer boot to activate the plug-in program, so you should first print the server power supply when using the printer power supply.

Q: Why can't I display the ink capacity, paper shortage, and other information after I use the printing server?

A: After the printer is used, the printer is connected to the application on the printer server and the printer status cannot be detected. This problem cannot be solved for the time being, which involves the technical copyright of the software.