SUSE Linux Enterprise Server SP4 (x86_64) bind dual NIC

Environment
SUSE Linux Enterprise Server SP4
Linux x86_64 x86_64 x86_64 gnu/linux

Configuration (/etc/sysconfig/network)
Ifcfg-eth0:

Device= ' eth0 '
Startmode= ' Auto '
bootproto= ' Static '
Master= ' Bond0 '
Slave= ' yes '

Ifcfg-eth1:

Device= ' eth1 '
Startmode= ' Auto '
bootproto= ' Static '
Master= ' Bond0 '
Slave= ' yes '

IFCFG-BOND0:

Bonding_master= ' yes '
Bonding_module_opts= ' mode=1 miimon=100 fail_over_mac=1 '
bootproto= ' Static '
Ipaddr= ' 168.192.10.100/24 '
Startmode= ' Auto '
Usercontrol= ' No '
bonding_slave0= ' eth0 '
bonding_slave1= ' eth1 '

#没有ifcfg-bond0 The file when the file is created, mode=1 hot standby mode (active-backup), VMware Workstation 11 I do not support the first way to get a MAC address, then you can use the fail_mac_over= 1 parameters. Of course, you don't have to do this in a real-world server environment.

Modifying the bonding configuration
Vi/etc/modprobe.d/bonding.conf
Alias Bond0 Bonding

Loading modules into the kernel

Modprobe bonding
Service Network restart
#insmod is generally required in a certain specification of the path, and will not be loaded in a dependent order module, and modprobe, different, it can be in any path, the need to automatically load the dependent module and bonding into the kernel.

View bonding Status

' Cat/proc/net/bonding/bond0
Ethernet Channel Bonding driver:v3.7.1 (April 27, 2011)

Bonding mode:fault-tolerance (active-backup) (Fail_over_mac Active)
Primary Slave:none
Currently Active Slave:eth0
MII Status:up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface:eth0
MII Status:up
Speed:unknown
Duplex:unknown
Link Failure count:1
Permanent HW Addr:00:0c:29:fb:3f:ab
Slave Queue id:0

Slave interface:eth1
MII Status:up
Speed:unknown
Duplex:unknown
Link Failure count:1
Permanent HW ADDR:00:0C:29:FB:3F:B5
Slave Queue id:0 '

bond0当前在使用的网卡是 eth0**其它linux环境**     在Redhat6.5 类似操作，绑定双网卡做热备成功 ifcfg-bond0 DEVICE=bond0TYPE=EthernetONBOOT=yesBOOTPROTO=staticIPADDR=168.192.10.12NETMASK=255.255.255.0GATEWAY=168.192.10.1USERCTL=noBONDING_OPTS="mode=1 miimon=200 fail_over_mac=1"ifcfg-eth0DEVICE=eth0TYPE=EthernetONBOOT=yesBOOTPROTO=staticUSRCTL=noMASTER=bond0SLAVE=yes ifcfg-eth1DEVICE=eth1TYPE=EthernetONBOOT=yesBOOTPROTO=staticUSRCTL=noMASTER=bond0SLAVE=yes**注意：Redhat 6 bond 配置修改路径** vi /etc/modprobe.d/dist.conf  alias bond0 bonding

SUSE Linux Enterprise Server SP4 (x86_64) bind dual NIC