Tp-link Router Setup Illustrated tutorial

device preparation for Tp-link router setup

First of all, the conditions are: router One (can be 4, 8 mouth, 16 or more, if you have a lot of computers, you can buy multiple switches. Cable line number, telecom mode one (or if you are a line that does not need mode), PC computer at least 2 units (if only one, Using a router is OK, but it loses the sense of using a router.

In fact, tp-link companies out of the router, such as Tp-link tl-402m or 401M or other models of Tp-link routers, the route to open most of the same. For example, in the following article, take Tp-link tl-402m, see picture 1

Figure 1tp-link tl-402m

Tp-link router introduced here, everyone as long as the introduction of the picture, the PC, Telecommunications broadband mode, routers, the correct connection to each other, then a network has been set up. The following describes how the sexual supplies sample open routing function.

　　The Tp-link router sets the previous period setting:

If the line has been picked up. We open a good PC computer at this time. Open the Network Neighborhood properties (Picture 2), Local Area Connection properties (Picture 3), TCP/IP protocol properties (picture 4), set IP to 192.168.1.2 Subnet: 255.255.255.0 gateway : 192.168.1.1 (picture 5) determines that DNS is set up at the end of the configuration router.

Note: You can go to the Control Panel network connection to set up.

Take XP For example, see Figure 2 to Figure 5 for details

Figure 2 Opening the Network Neighborhood properties

Figure 3 Local Connection properties

Figure 4 TCP/IP protocol properties

Figure 5 Setting IP, etc.

Yes, here to remind you, IP settings network segment, you can set up between the 192.168.1.2-192.168.1.254 can be, do not set the same IP to multiple computers, which will cause IP conflicts. Remember.

Then you can open the desktop Internet Explorer, enter 192.168.1.1 carriage return, see picture 6

Figure 6 Internet Explorer with desktop open

Here prompts the user name and password, the default username and password are admin, in the router instructions are also written. Enter and then press ENTER to enter the router configuration interface.

Note: The tplink router default IP is basically all 192.168.1.1 passwords are basically admin

　　Tp-link settings for router settings:

First access to the router interface, please see picture 7

Figure 7 Entering the router interface

Here we select the Setup Wizard. See picture 8

Figure 8 Selecting the Setup Wizard

Then next, see picture 9

Figure 9 Next

The choice of ADSL virtual dial-up, we are most of the choice of it, the other static that is the Green Line user choice, we do not do this in detail, know broadband users, railcom, Netcom and other virtual dial-up users, select it on the line, and then the next step see pictures 10

Figure 10 Next

Then click the next step, see picture 11, press completion to set up a good route.

Figure 11 Next

Then set in the DOT network parameters, WAN port settings, see picture 12

Figure 12 Network parameters

Okay, here's the configuration in the router. Everything is set up, now we only have to restart the router OK. Point System Tools, restart the router, after a few seconds, please see picture 13

Figure 13 Reboot the router

This time we turn off the configuration of the web window, the other computer can be connected to the Internet.

Note: Because this router's DHCP service is automatically opened, so you just connect PC computer, routers will assign IP, and so on to the computer, so the other computer basic need not set up, directly with the network cable to connect the router or switch to the Internet.

　　Details of Tp-link router setup:

Of course, you can set up IP manually:

IP Settings Range: 192.168.1.2-192.168.1.254

Subnet: 255.255.255.0

Gateway: 192.168.1.1

DNS: Local telecommunications-provided DNS can be set, with preferred DNS and alternate DNS

If you do not know the local DNS address, you can also set the preferred DNS to 192.168.1.1 is the gateway, the standby need not fill.

Okay, now go ahead. We need to set up the DNS address of this PC, the method is not more said, open the Network Neighborhood properties local connection properties TCP/IP protocol properties, see picture 14 for local telecommunications DNS address. Picture 15,dns as gateway address

Figure 14 Local telecommunications DNS addresses

Figure DNS is a gateway address

Note: Image 14 above is a local telecommunications DNS address, friends need to set up according to their local telecommunications DNS address.

The entire contents of the router Setup diagram are introduced to you here, hoping to help you understand and master the router settings.