TP-LINK Wireless Broadband Router

Hardware connection: Host-modern-Router

Set: IP Address: 192.168.1.x (the range of X is 2 to 254)

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

DNS asks the local network service provider (note: the DNS information must be the same as that in the "Wan port status" of the router)

Log on to the web management page: Enter http: // 192.168.1.1 in IE

Initial username and password: Admin

After entering the interface, select the setting wizard and set it according to the setting wizard.

If you cannot enter the Routing Management Interface, reset the router before setting it.

 

Appendix: TP-LINK product reset Daquan

Broadband Router:

1), with M1, M2 lamp TL-R4XX, TL-R4XXX next-generation network bar and TL-FR5300 Firewall Router reset method:
There is a small hole in the front/back panel of the router with the words:Reset
To turn off the power of the router, find the tip of the pen and press the reset key to power the router (still need to pressReset
Key). Wait about 3-10 seconds. After the M1 and M2 lights flash three times at the same time, you can release the device and reset the device;
Note:
After resetting, the router will be restored to the factory settings. The default logon IP address is 192.168.1.1, and the default username and password are admin/admin, when logging in, please note that your computer's IP address is in the 192.168.1.x (X is 2--254) network segment!

2), with PWR, sys light router and TL-FWR1100, TL-FR1000 two Firewall Router reset method:
Disconnect the power of the router and hold down the router with a tip object (such as a pen tip)Reset
Button is not put, re-power in (this process still needs to be pressedReset
When the Sys indicator is blinking, release the reset button. Then, the router will return to the factory status.
Note:
The power cannot be switched off before the router is fully started. Otherwise, the configuration may not be restored to the default value. After resetting, the router will be restored to the factory settings. The default logon IP address is 192.168.1.1, and the default username and password are admin/admin.
Soho routers using this reset method are: TP-R410 +, TP-R460 +, TP-R860 +, TP-R1660M.

3) methods for resetting a vro:
TL-R420 reset method: PressReset
After the key is released for about 2 seconds, the router will be restored to the default factory value. Default management address: 192.168.1.1; default username and password: admin/admin;
TL-R400 + reset method: power off, press and holdReset
Button, and then turn on the power (this process still needs to be pressedReset
After about five seconds, the router will be restored to the default value. Default management address: 192.168.123.254; default user name and password: admin/admin;
TL-R400 reset method: press the reset key about 2 seconds after the release, the router will restore to the factory default value. Default management address: 192.168.123.254. Default user name and password: admin/admin.

Wireless:

1) methods for resetting a wireless router:
TL-WR841N reset method: in case of power-on, please press 3 times in 5 secondsReset
Button. Then, the router will restart,
After the restart, the router will be successfully restored to the factory settings.
TL-WR3xx/TL-WR5xx/TL-WR6xx reset method: power off first, then pressReset
Press or hold the key, and then turn on the power.Reset
Key), wait until the system light flashes three times and then releaseReset
The router is restored to the default factory value. Default management address: 192.168.1.1; default username and password: admin/admin;
TL-WR240 +/wr240 2.0 reset method: PressReset
After the button is released for about 10 seconds, the router will be restored to the default factory value. Default management address: 192.168.1.1; default username and password: admin/admin;
Wr245 ver1.0 reset method: Press and holdReset
If the key is greater than five seconds, the router will be restored to the default factory value. Default management address: 192.168.1.1; Default User Password: admin/admin;
Wr245 ver2.0 reset method: Turn off the power supply, press this button, and then turn on the power, about 3 seconds, the system light is off and then on, the router will be restored to the factory default value. Default management address: 192.168.1.1. default username and password: admin/admin.

2) Wireless AP reset method:
TL-WA501G reset method: power off first, then pressReset
Press or hold the key, and then turn on the power (you still need to pressReset
Key). After 3 seconds, the system light is turned off and then on, and the AP is restored to the default value. Default management address: 192.168.1.1; default username and password: admin/admin;
TL-WA200/TL-WA200 + reset method: power-on status PressReset
5-10 seconds after the button, when the WLAN indicator turns from off to slowly shining, it indicates that the reset is successful. The IP address of version 3.0 is 192.168.1.100, the default user name and password is admin, And the IP address of Version 3.1 is 192.168.1.1, the default username and password are admin and Admin.
Vswitch type:

Vswitch:

WithReset
Key switch: TL-SL2210web, TL-SL2218web, TL-SL2428web, TL-SL2452web, TL-SG2109web, TL-SG2216web, TL-SG2224web. The methods for resetting these vswitches are the same as those for vrouters: power-off first, press and holdReset
When the power is turned on, all the lights are blinking, And the reset is successful. The default Management address is 192.168.0.1, and the default user name and password are Supervisor/supervisor;

TL-sf2226p +/TL-sl2226p + reset method: TP-LINK
In The SSU Management Program, click "device"> "Restore factory settings" to restore the switch to the default factory value. The default Management address is 192.168.0.100, And the account name and password will not be restored;
You can also connect to the vswitch through a serial port through the Super Terminal and telnet to reset the vswitch. (Note: If the password of a common user is forgotten, you can only log on to the Super Terminal using the administrator password. The Administrator
The password is set to admin and cannot be modified. After logon, you can directly change the password of a common user)
TL-SF2108P, TL-SF2109P,
TL-SF2808P, TL-SF2216P, TL-SF2224P, TL-SF2232P, TL-SL2226P, TL-SF2008,
TL-SF2117P, TL-SF1016V, TL-SF1024V, TL-SG2008 reset Methods: this series switch uses TP-LINK
The SSC program can be managed without the user name and password;

TL-SF3226P, TL-SF3008, TL-SF3117P, TL-SL3428, TP-SL3452, TP-SG3109 and partial Web Management
Type Switch reset method: through the serial port to connect to the switch, using the Super Terminal to log on to the switch, there is a prompt interface before starting the switch, press the CTRL-B key to enter the bootmenu, see
"Please input bootrom password:", Press enter, and select "3: Restore Factory
Default
Setting "to restore the switch to the factory settings, and then select" 5: reboot. The default Management address is 192.168.0.1, and the default user name and password are
Supervisor/supervisor.

ADSL:

TD-W8900G/w8910g/w8920g reset method: disconnect the router power, with a tip object (such as pen tip) Press and holdReset
Do not place the button, re-plug in the power, lasting more than 5 seconds, releaseReset
Button, reset successful.

TD-8820 (including enhanced) reset method: Hold down with a tip object (such as a tip) when the TD-8820 is runningReset
The button is not placed and lasts for more than 15 seconds. ReleaseReset
Button, reset successful.

TD-W89541G (including enhanced) reset method: Hold down with a tip object (such as a tip) when the TD-8820 is runningReset
The button is not placed and lasts for more than 5 seconds. ReleaseReset
Button, reset successful.

TD-8800 reset method: in the case of continuous power, continuous pressReset
Press the button three times, the indicator lights are all flashing, And the reset is successful. Default management address: 192.168.1.1; default username and password: admin/admin;

TD-8810/TD-8810 +, TD-8610/TD-8610 + reset method: first power off, then pressReset
Key, then turn on the power, wait about 3 seconds, reset successfully. Default management address: 192.168.1.1; default username and password: admin/admin;
TD-8830/TD-8831 reset method: in the case of continuous power, press and holdReset
The key lasts for about 10 seconds, and then is released. The Reset is successful. Default management address: 192.168.1.1. default username and password: admin/admin.

Print Server:

TL-PS110P/ps110uReset
Function key, clickReset
The key is restarted.
TL-PS110P/ps110u reset method: first power off, then pressReset
When the key is not relaxed, power-on will wait for 5 seconds before it is released, that is, the factory settings will be restored. After the management password is reset, it will become the initial password-less status. The IP address of the TL-PS110P is not restored to the default 192.168.0.10, but remains the last configured IP address. Note: The reset key of the TL-PS110P is on the side and the reset hole is small.
TL-PS210U reset method: power off, hold downReset
Hold down the key and connect it to the power supply for 5 seconds.Reset
Key, the printing server will be restored to the default factory, the IP address will return to the default IP Address: 192.168.0.10.

TL-WPS510U reset method: power off, hold down the reset key do not put, power on 15 seconds after releasing reset key. Wait about 40 seconds and the device starts successfully. TL-WPS510U works by default
In ad-hoc mode, the SSID number is WLAN-PS, default Management IP Address: 192.168.0.10, Management User name: Admin, password: 0000 (4 digits
0 ).
Our printing server's default Management IP address is 192.168.0.10. Before using it, determine whether the IP address of the computer and the printer server is in the same network segment.