What is the tp link router address? What can I do if I cannot log on to the management interface?

1And confirm that the logon management interface is correct.

As shown in the following figure, open the browser and enter 192.168.1.1 in the address bar (note that "." in the middle cannot be entered as "."), Press Enter. If it still cannot be opened, proceed to the next step.

 

 

 

2, Check and confirm that the device connection is correct.

As shown in the following figure, the computer network cable connects to the vro1 LAN1 ~ 4. Check and confirm that the status of each indicator is normal.

 

After confirmation, open the browser, Enter 192.168.1.1 in the address bar, and press Enter to log on to the vro management interface. If it cannot be enabled, continue with the next step.

 

3Check and confirm that the computer network parameters are correctly set.

All computers can automatically obtain IP addresses by default. Different operating systems can be set as follows:

Windows 2000/XPSystem:Double-click the local connection"Small Computer"Icon (if there is no Nic icon in the lower right corner of the computer, enter the"Start--Control panel --Network connection --Double-click local connection"), And then configure according to the following figure.

 

Windows 7/VistaSystem:Click the network connection icon in the lower-right corner of the desktop, and click"Open Network and Sharing Center--Change the adapter settings/Manage network connections --Right-click the local connection --Attribute"(Or click"Start button--Control panel --Network and Internet --Network and Sharing Center --Change the adapter settings/Manage network connections --Right-click the local connection --Attribute"), And then configure according to the following figure.

 

 

For Apple iMac or Macbook, see:

Http://service.tp-link.com.cn/detail_article_196.html

 

After the above configuration, the computer will automatically "ask for" the IP address from the router, the router will also assign parameters to the computer after receiving the request, and then click the "small computer" icon in the lower right corner of the computer,"Supported"Tab, you can see the computer parameters, as shown in the following figure (take the XP system as an example ):

 

After setting, log on to the vro1.1 management interface 192.168.1.1. If it cannot be enabled, continue with the next step.

 

4And restore the router to the factory settings.

You can refer to the instructions for the method. The vast majority of TP-LINK router reset method is:When the device is powered on, press and holdResetKey 5About seconds, SYSIndicator lightThe flash starts three times and the reset is successful.. After the factory settings are restored, log on to the vro management interface 192.168.1.1. If it cannot be enabled, continue with the next step.

 

5, Check and confirm that the browser settings are correct.

Change the web browser or computer, and try to log on to the router settings page. If there are no other browsers or computers, check whether the browser has set the wrong proxy information. The check method is as follows:

Open the IE browser and click"Tool --InternetOption"Select"Connection"Tab, select"Never make a dial-up connectionClickLAN settings", Make sure that the three options are not selected, as shown in the following figure, and click"OK", Return to the previous Internet Options dialog box, and click"OK".

 

Disable the offline status, which affects normal webpage browsing. In the displayed "offline web page unavailable" prompt, select a connection, or click the browser"FILE-working offline", Offline work is not checked.

 

After setting, log on to the vro1.1 management interface 192.168.1.1. If it cannot be enabled, continue with the next step.

 

6Confirm the computerARPThe information is correct.

Unplug all other computers on the LAN port of the router, retain only one computer, and clear the ARP cache information of the computer. The method is as follows:

Windows XP:Click"Start -- run", Enter"Cmd", Click"OK", In the pop-up DOS interface, enter the command"Arp-dAnd press Enter.

Windows 7:Click Start and enter"Cmd", Find the cmd program, right-click the program, and select"Run as Administrator", Enter the command"Arp-dAnd press Enter. As shown in the following figure.