Windows 7 startup problem with blue screen stop:0x0000007b

Source: Internet
Author: User
Tags requires

Workaround: Boot into the BIOS, change interface combination, that is, the type of interface of the hard disk, changed from default raid to AHCI, save, reboot, all normal.

Event procedure:

Today, the boot into the Win7, in the start Windows suddenly encounter a blue screen, the above a pile of English prompts I said is recently installed hardware or software, so I took out the CD-ROM, wireless mouse receiver unplug, restart, the same as.

Because I installed a dual system, into Linux, but everything goes well, so the elimination of hardware problems, the problem is out of the Win7, and will not be the problem of guidance (formerly lead always out of a variety of egg pain, but the wood has a blue screen.) )

Later, the thought is in the Win7 shutdown, forced shutdown caused by the problem, the results in the selection of Win7 boot when the F8, and then select System repair, System Restore a week ago, the most recent normal start, and so on, the problem is still the same.

Finally, insert U dish, enter pe,pe everything goes well. At this time, I began to suspect that the problem is hard disk, plus, Linux can be launched smoothly, so the problem points to the drive, is Win7 hard drive problem, but why used to good, why suddenly can not go in. At this time, I suddenly remembered, just I want to change CentOS to Fedora, the media is the use of the disc, but can not normal boot CD (boot order has been changed), so the hand cheap pressed F9, restore the default configuration, so the BIOS inside the interface combination ( Interface combination) into raid, and after the AHCI, everything goes well.

See more highlights of this column: http://www.bianceng.cnhttp://www.bianceng.cn/OS/home/

Postscript:

1, when encountering problems to think more, slowly ruled out. Unless it is a hardware problem, hard drive bad way or fall of the problem, or else, there will always be a solution, reloading system is the most unwise, if this problem, the reload system may or cannot be resolved, because Win7 may not be the drive with raid.

2, encountered no problem, many Google, if the earlier Google, the problem can be solved in a minute, the result wasted a lot of time.

With a piece of other people's articles, there are many summaries about stop:0x0000007b. http://ddazhanhongtu.blog.163.com/blog/static/1763870752012101465011974/

0X0000007B This code has to do with the hard drive, but don't be afraid, it's not bad, it's a setup problem or the hard drive partition error caused by the virus.

If you are using the original system disk to install the system when the problem, it shows that your machine configuration is relatively new, as the old system disk, do not recognize such a new hard disk interface, so the BIOS to the hard disk mode into the IDE compatibility mode. Of course, people now use the ghost version of the operating system, compared to the new ghost disk is not the problem. About the problem that people can't find the IDE, because many motherboards indicate that the wording is not quite the same as some of AHCI and compatibility, this AHCI is equivalent to SATA mode, compatibility is equivalent to IDE mode.

If your operating system has been used for some time, and suddenly one day this problem, then I am sorry, the virus caused by the boot press F8, select the last correct configuration, restore the normal mode then please do the system again.

The motherboard starts the AHCI mode backward system blue screen prompt "0X0000007B". The hard drive is not detected by the reload system. However, the motherboard BIOS shows the hard drive exists.

This is typical without the pre-installed AHCI drive, there are two solutions, the first is not to reinstall the system, the user can set the BIOS to "IDE" mode, so that the system can be normal, and then according to the motherboard chipset download the corresponding AHCI driver and installation, (such as Intel's download of Intel Matrix Storage Manager, and then the installation program, AMD platform, the need to modify the registry, the method is more complex), and finally change the BIOS back to "AHCI" mode, restart it. There is also a second approach, which requires reinstalling the system, and pressing F6 to install AHCI drive through the floppy drive during the installation of the system, which requires the software to reload the system, and recommends that the first solution be adopted.

At present, many motherboard bios in the SATA mode option is the default setting is the IDE model, the user installed in this mode after XP, if the direct SATA mode in the BIOS from the IDE to the AHCI model, the XP startup will be due to not preload SATA AHCI The controller driver appears with a blue screen.

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.