WISP > Client+ap > WDS differences

The most straightforward distinction: WISP > Client+ap > WDS

WISP, truly omnipotent, compatible with any brand of superior APS, do not have to set superior APS, not affected by the channel of the superior AP, free DHCP, the IP with the machine or device, the superior AP will not be displayed.

Client+ap, limited omnipotent, compatible with any brand of superior APS, do not have to set up superior APS, by the superior AP channel influence, no DHCP, with the machine or device IP, the superior AP will be displayed.

WDS, subject to more restrictions, cannot be compatible with any of the brand's superior APS, this one is the key.

1, wisp (equivalent to the WAN port of the cable router) and WAN port status related to know that the WAN port can be set static IP can be automatically obtained IP (from the superior) DHCP without shutting down the network segment with the superior can be turned into wired wireless internet access

Client+ap (equivalent to the LAN port of the wired router) is not connected to the WAN port State. DHCP Shutdown network segment with superior same network segment can be transferred to wired wireless internet access

I don't know if you can understand.
WDS Bridge scrap function only the pure bridging function needs to be in the primary sub-routing setting

1, Bridge, WDS need to set their own route to the other side of the Mac, if the two routers are their own, you can use this ways. If it is ceng to the net, can enter the route fortunately, if you do not go to the route, WDS will not be. can only be used WISP Universal relay. 2, Wisp can receive WEP, WPA, WPA2 encrypted wireless signal, after amplifying the signal and then switch to network cable and wireless signal with When output. 3.WDS mode, wireless cable will not slow down, DD Universal Relay has netizens reflect the situation of wireless spin down, but I from Using the tenda308r, 150M wisp experience, no spin down. Theoretically speaking, Wisp is a combination of client Nic +ap, there is no spin down this said. may be self-brushed dd, unstable Caused by. 4, WDS Bridge, the second AP must turn off the DHCP service function, IP allocation to the first upstream primary AP, this is not Will exactly The WISP does not need to turn off DHCP. 5, WDS and bridge are not very different, bridge can be a pair of more, WDS can be many to one. 6, support WDS mode of a lot of routes, basically now the new router are supported, do not need to brush the firmware. If you want to use DD million Can relay to buy the router to support the DD firmware to brush, and seemingly partial route brush DD firmware after a bit acclimatized, Some of the route brush bad also directly brick, or with cheap original wisp easy to use. Of course, playing relay is not necessarily CEng network, there are many features. When bridging, relaying, for stability, it is recommended to choose 11g, do not choose 11BGN blending mode

Bridge, WDS needs to be routed to the other side of the router to set its own Mac, if the two routers are their own, you can use this

ways. If it is ceng to the net, can enter the route fortunately, if you do not go to the route, WDS will not be. Can only be used

WISP Universal relay.

2, Wisp can receive WEP, WPA, WPA2 encrypted wireless signal, after amplifying the signal and then switch to network cable and wireless signal with

when output.

3.WDS mode, wireless cable will not slow down, DD Universal Relay has netizens reflect the situation of wireless spin down, but I from

using the tenda308r, 150M wisp experience, no spin down.
Theoretically speaking, Wisp is a combination of client Nic +ap, there is no spin down this said. may be self-brushed dd, unstable

caused.

4, WDS Bridge, the second AP must turn off the DHCP service function, IP allocation to the first upstream primary AP, this is not

. The WISP does not need to turn off DHCP.

5, WDS and bridge are not very different, bridge can be a pair of more, WDS can be many to one.

6, Support WDS mode of a lot of routes, basically now the new router are supported, do not need to brush the firmware. If you want to use DD million

can relay to buy the router to support the DD firmware to brush, and seemingly partial route brush DD firmware after a bit acclimatized,

some of the route brush bad also directly brick, or with cheap original wisp easy to use.

of course, playing relay is not necessarily CEng network, there are many features.

when bridging, relaying, for stability, it is recommended to choose 11g, do not choose 11BGN Blending mode

WISP > Client+ap > WDS differences