Zabbix Enterprise Applications: monitoring Dell server hardware through SNMP and Idrac

There are generally two ways to monitor Dell server hardware: 1, install OMSA on the operating system, write scripts to invoke the omreport command to monitor; 2. With Idrac, you can not install OMSA on the operating system, just The Snmp,zabbix on Idrac is monitored via SNMP. For operating systems that do not support Omsa and the requirement that additional software cannot be installed, SNMP monitoring is recommended and the configuration is simple and convenient.

First, Idrac open SNMP Service

Enter IDRAC Web interface, open "network", "Services", "SNMP agent".

650) this.width=650; "src=" Http://s5.51cto.com/wyfs02/M02/7D/37/wKiom1bibZKjCpKEAADo0dCO070480.png "title=" IDrac Snmp2.png "alt=" Wkiom1bibzkjcpkeaado0dco070480.png "/>

SNMP is enabled and the Community name (community) is set, and the default public is not recommended. It is recommended that all servers set a uniform community name.

Then test on the Zabbix server server to see if you can get to the data:

Snmpget-v 2c-c <Community> <idrac ip>. 1.3.6.1.4.1.674.10892.2.1.1.2.0

650) this.width=650; "src=" Http://s2.51cto.com/wyfs02/M00/7D/36/wKioL1bigmOxt6u7AAAR7VEmcIU647.png "title=" Snmp_ Get.png "alt=" Wkiol1bigmoxt6u7aaar7vemciu647.png "/>

Second, the configuration Zabbix

1. Create Value Mapping

delldracdiskstate1  unknown2  ready3  online4  foreign5   offline6  blocked7  failed8  non-raid9  removeddell idrac  network device connection status1  up2  down3  driverbad4   driverDisabled10  hardwareInitalizing11  hardwareResetting12   hardwareclosing13  hardwarenotreadydell open manage system status1   other2  unknown3  ok4  noncritical5  critical6   Nonrecoverabledellpowerstate1  other2  unknown3  off4  ondell psu  State Settings1  Unknown2  Online  (state disabled) 4  not  ready8  fan failure10  online and fan failure16  on242   online and okdellraidlevel1  unknown2  raid-03  raid-14  raid-55  raid-66   RAID-107  RAID-508  RAID-609  Concatenated RAID 110   Concatenated raid 5dellraidvolumestate1  unknown2  online3  failed4   DegradedDell_PSU_SensorState1  Presence Detected2  PS Failure4   predictuve failure8  ps ac lost16  ac lost or out  of range32  AC out of range but still present64   Configuration error

2. Import templates

Select Configuration->templates->import to import the templateDell iDrac SNMPV2templates.

the template is shown in the annex, " Template Dell IDrac SNMPV2 zbx2.2.xml "supports zabbix2.2 version," Template Dell IDrac SNMPV2 zbx3.xml "supports the ZABBIX3 version.

The following monitoring categories are supported for templates:

• Disks/storage (disk)

• Fans(fan)

• memory (RAM)

• Network Cards(network card)

• Power(mains)

• Processor(CPU)

• System Info

• Temperatures(temperature)

• Voltages(voltage)

The template was downloaded from GitHub, and I modified some errors and optimized them.

3. Configure global Variables {$SNMP _community_idrac}

Select Administration->general->macros, create variable "{$SNMP _community_idrac}", fill in IDRAC's web in value The SNMP Community name (Community) configured on, such as:

650) this.width=650; "src=" Http://s1.51cto.com/wyfs02/M02/7D/36/wKioL1bifJyQ9B1MAACBHd0d7ls776.png "title=" Macros.png "alt=" Wkiol1bifjyq9b1maacbhd0d7ls776.png "/>

4. Create a host

Enter the host Configuration screen, and remember to fill out "SNMP interfaces" as the management address of IDrac and link "templateDell iDrac SNMPV2" templates.

Note: The monitoring interval (Update interval) for some of the monitoring items in the template is 86,400 seconds, and it will take about a day for the first data to be monitored.

At this point, all configurations are finished ~

This article is from the "Start Linux blog" blog, make sure to keep this source http://qicheng0211.blog.51cto.com/3958621/1749986

Zabbix Enterprise Applications: monitoring Dell server hardware through SNMP and Idrac