Installing the Win7 system is a tip: Windows Setup cannot configure Windows to run on this computer's hardware

Bowen is reproduced from Afeia, the copyright belongs to the original author.

This article solves the author's question, therefore reproduces, hoped can solve more people's question.

The installation of the WIN7 system appears: "Windows Installer cannot configure Windows to run on this computer's hardware", such as:

Workaround:

When prompted, pressing SHIFT+F10 will open the command window,

Go to the C:\windows\system32\oobe folder, enter Msoobe carriage return and enter Msoobe to proceed to the next step.

But the error box is still in, don't bother. follow the on-screen prompts to enter the appropriate information until you complete the installation of the system. After installing the WIN7 system, there is no problem.

The above situation generally appears in the ghost version of the WIN7 system.

I have met two times, are resolved through the above method:

1. Acer D270 installs the win 7 32-bit flagship Ghost edition;

2.HP installed green tea Ghost WIN7 32-bit Professional Edition;

———————————————–

Note: Do not DOS command, do the following: Hold down the SHIFT key and then press the F10 key, open the command window, enter CD OOBE carriage return, and enter Msoobe

———————————————–

Search the web for the problem and find the following solutions:

1 Netizens said that as long as the ghost system to copy to the USB stick installation can solve the problem; a netizen said that copying the ghost system to a hard disk installation solves the problem.

2. Some netizens say that the problem is hard drive boot, rebuilding the MBR can solve the problem.

3. Some netizens think that it is WIN7 hide the problem of the partition (WIN7 another way of installation, in the hard disk recommended 100MB active hidden partition for the boot file), the solution is: Install the installation version of the system, in the steps to the partition to remove the C drive, At this point, you are prompted to create a hidden partition, after you establish a hidden partition, exit the installation and then install the Ghost version of the system, and then perform a system repair installation.

4. A netizen said, to the official website of Intel Download 3 Series chipset windows 7 F6 driver, install the driver can be loaded.

Analysis: 1th, 2 The solution is basically a rip-off, and the 4th is probably right, but I think the problem with driver class is usually a blue screen instead of appearing as an error prompt. 3rd, the solution is too cumbersome and too time-consuming.

Cause of the problem: it should be the reason why the hard disk has two primary partitions! WIN7 installation There are two ways, one, is the WIN7 system boot files and system files are stored in the C drive (at this time the C drive is the active primary partition), and two, WIN7 boot files are stored separately in the 100MB-200MB hidden active partition, System files are stored in the C-drive (C-disk is inactive primary partition)-random WIN7 system, which is generally used in this way of installation.

There are active hidden partitions of the installation of the ghost version of the WIN7 system, will be a blue screen or continue to restart the system can not successfully install the phenomenon. When you set the active hidden partition to an inactive partition and set the C drive as the active partition, it is very likely that you will encounter the scenario when you install the Ghost WN7 system.

Original:

Workaround:

When prompted, press SHIFT+F10 will open the Command window, go to the C:\windows\system32\oobe folder, enter Msoobe return and enter Msoobe to enter the next operation, but the error box is still in, Don't worry. Follow the on-screen prompts to enter the appropriate information until you complete the installation of the system. No problems with the WIN7 system after installation.

-----------------------------------------------

140918 Additional notes:

1. Do not DOS command, please refer to the method: When prompted, press SHIFT and F10 function keys, this time will jump out of the command window: Please enter the cd\ and press ENTER after the return to the root directory, the screen is displayed on the c:\>; Then enter the CD windows\system32\oobe the OOBE folder is now entered, and then enter Msoobe to jump out of the next steps.

Unfamiliar to find a functioning win 7 system to do a real operation, method: Enter into the win 7 system, start-run-Input CMD Open Command Window-follow the above 1 method to enter the OOBE folder, enter Msoobe, will jump out of the system installation interface.

2. This method applies the error message that occurred during the other installation process, such as:"The computer restarted unexpectedly or encountered an error." Windows installation cannot continue. To install Windows, click OK to restart the computer, and then restart the installation. If you encounter such a hint, you will end up with the same error message after you confirm the point. Refer to the above method to skip the error prompt and proceed to the next installation process. If a blue screen occurs when you enter the system desktop, you can try to enter Safe mode first, and then restart the system after the general smooth access to the system. This can be caused by a driver problem (ghost has been added or truncated by a third party driver, installation of the wrong driver or driver missing may cause a blue screen, landing security mode may fix driver errors), which explains why some computers can successfully install Ghost system,   And another computer installed the same ghost system will jump out of the prompt. The computer is the same principle and function, the difference is only the hardware is different then it needs the hardware driver is not the same, the reason for the reasoning will be the cause of the error: May be a driver problem. Note: just guessing!

-----------------------------------------------

Installation System FAQ :

1. Back up important information and files such as photos and QQ chat Records , if you can not enter the system available USB disk boot disk into WinPE after the files copied to the USB flash drive. It is recommended to back up important data in the USB flash drive before installing the system, the partition table error encountered during the installation, or the wrong installation to another data tray and other problems can result in data loss. If you lose important information, immediately shut down and take the hard drive to the data recovery company for data recovery, at this time, any drive operation, such as an open machine will affect the data recovery.

2. Before installing the network card or the wireless card driver to download back, because the network card or wireless card type is different, the system's general-purpose driver is not necessarily suitable for all network cards.

3. It is better to format the C drive before installing the system, otherwise it will probably become an overlay installation.

4.WIN 7 users of the system need to pay attention to a problem:WIN 7 Installation has two methods , one is to put the hard disk 100-200mb space to hold the system boot boot file, the space is the main active hidden partition, At this time, the C disk is not active partition if the system installed in the C drive system can not be started-symptoms: jumping out of a line in English prompts to find the system, or directly to the blue screen, the solution is: directly with the hardware partition software to set the C disk as the active partition and then install the system to the C drive . The second is the system system files and boot files are stored in the C drive, at this time the C drive is the active primary partition.   The WIN 7 Ghost Edition system basically installs the boot files and system files directly on the C drive. purchased brand computer and has installed genuine Win 7 system, mostly divided the 100-200mb of hidden active partition, installation should pay attention to this problem.

5. Blue screen problem: mostly caused by two reasons, one is the previous problem of hidden partition, and the other is hard disk drive problem, hard drive problem Resolution: 1. The simplest is to download a win 7 Ghost system from another website, and then the next one, Generally three different ghost should be available for most systems.  2. Enter the BIOS system to change the hard drive mode to IDE, and vice versa to AHCI mode. 3. There is also a way to drive offline injection: A lot of u disk boot disk with this function, the more you can try.

6. Unable to boot the system problem: After successfully installing the system after reboot prompted to find the system or the normal operation of the win 7 system suddenly failed to start, This may be due to the following reasons: 1. Check if USB is connected with a USB flash drive or a removable hard disk, and the individual computer can not start the system with a removable hard drive; 2. boot file missing or damaged, symptoms: computer on a line of English tips can not find the system, the solution with a U disk boot repair boot file to solve it-- e system, the program can be found in the start program. 3. Hard disk MBR boot area problem, cause unable to start, like installing a key wizard or other software that will write data in the hard disk boot area may encounter such problems, the solution is to use hard disk partition software disk Genius rebuild MBR (this operation will not destroy the data stored on the hard disk).

7. How do I enter the BIOS setup interface? --General desktop is del key, books are ESC, F1, F2, how to make a USB flash drive or optical drive priority?   Most computers press F12 on startup to jump out of the selection menu, select a USB drive or CD drive to confirm. Samsung has a model do not remember, enter the BIOS must be cold start to enter the--that is, the first time to enter the BIOS exit, you have to shut down the restart to enter the Biso interface, otherwise, how can not enter the BIOS, special let people tangled.

The author adds: Using the desktop in the installation of the Win7 system, after entering the BIOS system, some brand of computer not only need to set the USB flash drive as the first startup item, in addition to the first boot option above there is an option, enter and then will contain the words of the U option pinned, so as to successfully become the first USB flash drive.

P.S. If the article infringes your interest, or you do not want others to reprint it, please let me know.

Installing the Win7 system is a tip: Windows Setup cannot configure Windows to run on this computer's hardware