Port ing methods for various ADSL Modem and vro

Port ing methods for various ADSL Modem and vro

Enter the router address in the address bar of IE (the default ip address is 192.168.1.1, the user name is admin, And the password is admin ), in IE, a window is displayed asking you to enter the "user name" and "password" of the vro. The implicit setting of MT800 is admin/admin.
On the settings page of MT800, click "other settings" in the upper left corner. Select "NAT" (in the drop-down menu of "other settings)

On the "NAT" page, first confirm that the "NAT" option is "allow", and then click Add

In the pop-up "NAT rule adding", a table is displayed, Which is changed as follows:
RULE FLAVOR RDR
Set rule id to 2.
Select ppp-0 in IF NAME
Select TCP in the Protocol
Enter 192.168.X.X in the Local address From (this is your internal IP address. If the IP address is changed, modify it in the future)
Enter 192.168.X.X in the Local address.
Do not fill in the Global address from and to, that is, keep 0.0.0.0
Fill in the last three ports (the starting value of the target port, the ending value of the target port, and the Local port) in the TCP port you want the BS to open (the BS defined setting is 16881, here we enter 16881 to 16889)

After the submission is complete, even IF the port image is done. IF not, the possible error is if name (may be a ppp-1)

China Digital DCAD-6010RA ADSL route settings
First, log on to the vro Web Management Interface (the default ip address is 192 .. 168.1.1, the user name is adsl, And the password is adsl1234)
Select Services> NAT in the following order.
Select NAT Rule Entry in NAT Option. Click "add", and then enter the corresponding parameters on the following page.

Click Submit after setting.

The parameters are described as follows:
Rule Flavor: Rule type
Rule ID: identifies the sequence number of an address translation Rule. The smallest sequence number is executed first. If the Rule is correct, it is not executed against a higher ID.
IF Name: select the corresponding wan interface, such as PPP and 1483B.
Protocol: select the Protocol (TCP, UDP, ICMP, and so on)
Local Address From: Use the starting value of the Local IP Address of the rule. If you select all, enter 0.0.0.0.
Local Address To: Use the rule's Local IP Address end value. If it is a single IP Address, fill in the IP Address start value. If you select all, set limit to 255.0.
Global Address From: No need to modify
Global Address To: do not modify
Destination Port From: Port start value of the target IP address (16881)
Destination Port To: end value of the target IP address Port (16889)
Local Port: Local IP Port (0)

After configuring the ADSL route, various network cables, and switches, you can configure the Internet computer. Many people often do this. It must be noted that when using ADSL to share the Internet, each computer mainly sets three items in the network options, namely IP address, gateway, and DNS configuration. Many people make an error when the DNS and ADSL route settings are inconsistent. If no selection is made in the ADSL route settings (DHCP/DNS) ("Lan DHCP server" is not selected "), in the network settings of the computer, the DNS configuration cannot be selected from the DNS of the local ISP. In this case, enter the built-in IP address of ADSL in DNS. That is, in the network settings of the computer, the gateway and DNS are the same, and the built-in IP address of ADSL should be entered, and the IP address corresponding to the gateway is in the same network segment as the built-in IP address of ADSL.

Configure the port ing of Alcatel _ ADSL_MODEM511E
First, enter 10.0.0.138 in the browser window to enter the routing settings window.
Then, select "Advanced Configuration"> "NAPT"> "add"
Then select:
The communication protocol is TCP.
The internal IP address is the IP address of the NIC. If you do not know it, use 10.0.0.1.
Both internal and external ports are 16881
The external IP0.0.0.0 remains unchanged.

Similarly, an increase of 16882 ~ .

Last click "application"
Then remember to click the "Save all settings" option in the upper left corner.
Success! Please shut down and the adsl modem is powered off. Restart

Port ing method by Putian (GS8100)
General Day (GS8100) Port ing to raise the ID method (LAN Routing ):
Enter 192.168.1.1 in IE
Enter the Modem user name and password
"Service-NAT-select NAT Rule Entry from the drop-down menu"
Click "add"
A new window is displayed:
Rule ID: 2 (number in sequence, based on the original ing, if not, usually 2)
Rule Flavor: RDR
IF Name: ALL
Protocol: tcp
Local address From: 192.168.1.6 (your IP address in the LAN)
Local Address To: 192.168.1.6 (your IP address in the LAN)
Global Address From: 0.0.0.0
Global Address To: 0.0.0.0
Target Port start value: 16881
Target Port termination value: 16889
Local Port: 0
Click "Submit"
Then save and restart.

How to Set tengda TED8620
General Day (GS8100) Port ing to raise the ID method (LAN Routing ):
Enter 192.168.1.1 in IE
Enter the Modem user name and password
"Service-NAT-select NAT Rule Entry from the drop-down menu"
Click "add"
A new window is displayed:
Rule ID: 2 (number in sequence, based on the original ing, if not, usually 2)
Rule Flavor: RDR
IF Name: ALL
Protocol: tcp
Local address From: 192.168.1.6 (your IP address in the LAN)
Local Address To: 192.168.1.6 (your IP address in the LAN)
Global Address From: 0.0.0.0
Global Address To: 0.0.0.0
Target Port start value: 16881
Target Port termination value: 16889
Local Port: 0
Click "Submit" and save it. Restart the instance.

Port image settings for Itek (e. TEK. TD) TD-2018 cats
Open IE, ENTER the router address in the address bar, for example, 192.168.1.1 (implicit), and then ENTER
Fill in the login name and password in the pop-up login window (the implicit login name for the TD-2018 is empty, the password is 12345), and then click OK

Go to the web page of the TD-2018, find "port binding service" on the left, click "port binding service"

Enter the "port binding service" column. First, we need to create a TCP port image.
1. select TCP
2. Fill in the TCP port used by EMULE, and the implicit setting in EMULE is 16881
3. Enter the Intranet IP address of the host.
4. Click "add" to add TCP port ing as "Service List" (after adding, a port image service will be added to the "service list" below)
5. Similarly, join 16882 ~ 9 ing

Click "Save settings"
The TD-2018 port ing requires support from NAPT, checking whether NAPT is on
Click "NAPT" Settings
Select "enable NAPT" and click "run"

Click "restart". After the cat restarts, the port ing is completed.
Set ztx zte _ ADSL_831 port ing to open ie, ENTER the address of the cat in the address bar, for example, 192.168.1.1 (implicit), and ENTER
Fill in the login name and password in the pop-up window. ZXDSL831's implicit login name and password are both uppercase ZXDSL, and then click OK

Go to the WEB Settings page of ZTE ZXDSL831, find "SERVICE" in the upper-right corner, and click SERVICE

After entering the SERVICE, click "NAT" at the first place on the left, select "NAT Rule Entry" at the second place, and then click "add"

First, we create a TCP port image. The implicit TCP port used by BS is 16881.
1: Select RDR
2. Fill in a rule id and write a number as long as it is not repeated with the previous one. For example, you can take 16881
3. Select ppp-0 (this depends on your cat, but most cats use ppp-0)
4. select TCP
5. Fill in the Intranet IP addresses of your computer respectively. (Note: Sometimes the Intranet IP address may change. If there is any change, you need to go back and modify it accordingly)
6. The two addresses here do not need to be modified, so the IP address is 0.0.0.0.
7. Select "Any Other Port" for all three"
8. Fill in three TCP ports used by BS, such as 16881.
9. Add 16882 to the same method ~ 9
Click 9 to add

Return to the NAT column again, confirm that the NAT rule contains the IP address of the computer with the TCP port BS, and then click ADMIN

In "ADMIN", Click Commit & Reboot

Select "Reboot From Last Configuration", click "save", and then click "restart ".

Setting of Tianyi _ ADSL_HASB-100 port ing the implied address of Tianyi HASB-100 ADSL cat is 10.0.0.2 (factory default)

Open IE and enter the vro address (for example, 10.0.0.2) in the address bar to enter the vro logon window.
Enter the vro logon name and password in step 2. The default logon name is admin and the default password is epicrouter or conexant.
Click OK at 3

If the password is correct, IE will go to the cat's WEB configuration page and click "virtual server" in the lower left corner"

We need to make two port maps, one is the TCP port of bs (default is 16881)
Of course, you may not use the default bs port number.

1. Enter a number in the ID number to map the number to this port, for example, 81.
2. Fill in the public port column and the private port column with the TCP port used by BS (16881 by default). The numbers in these two columns must be the same.
3. Select "TCP" as the port type"
4. Fill in your intranet IP address, for example, 10.0.0.8 (the Intranet IP address can be viewed on the top floor)
5. Click "add Settings" to add the port ing to the NAT rule.

Click "Save settings ". In the same way, do 16882 ~ 9.

Click "Save settings" and restart the cat. The setting of the port image is complete.
The real-time _ ADSL_2110EH port ing settings assume that the Intranet IP address is 192.168.10.2.
Use http: // 192.168.10.1 in IE to open the Real-Time ADSL management configuration page
Username: ROOT
Password: GROUTER
1. Select Service → NAT Options: NAT Rule Entry → Add → enter the port ing page
2. Add:
Rule Flavor: RDR
Rule ID: 2
IF Name: All
Protocol: TCP
Local Address From: 192.168.10.2
Local Address To: 192.168.10.2
Global Address From: 0.0.0.0
Global Address To: 0.0.0.0
Destination Port From: 16881
Destination Port To: 16889
Local Port: 0
3. Select Submit to Submit
4. Select Admin → Commit & Reboot → Commit → restart Modem in the Main Window menu.
OK
Good luck.

In addition:

Root/grouter is the default user name and password
You can try the following two usernames and passwords:
User/starnet
Admin/starnetadsl
Daya technology DB-108 router port ing method in-top: Daya 108 full strategy (routing method, port ing method)
I. Routing setting method:

1. First, the hardware is connected, and the current switch does not have UPLINK ports. Check whether the device's PC indicator is on! If it is on, OK!

2. for network configuration, be sure to have the correct protocol installed on both the adapter and TCP/IP! Set your IP address under the IP address tag to (192.168.1.2 ---- 192.168.1.254), because it must be in the same network segment as your device! Remember to set up DNS. I don't know. Call China Telecom to ask.
Check whether the connection is correct: run the following command to "ping 192.168.1.1" to check whether the connection times out! If it does not time out, OK!
If your system is 2000 or XP, you only need to choose to automatically obtain the IP address and DNS. However, if you want to connect two machines to the Internet, you can also set up IP addresses,

3. Open IE, enter "192.168.1.1" in the address bar, and enter your username and password in the window that appears! Can be found in your manual! Here, I entered the Default User and password for "admin" and "dare" factory! Some passwords are: dareadsl
If it cannot be accessed, Please reset the hole after the PIN is inserted three times in case of power-on (the cat has been set for the factory )!

4. Click WAN under configuration on the left. This is a side page to go to the settings page! Here is the most important thing. I am a user in Fuzhou. I also need to ask you about the specific settings of the local telecommunications department!
Click "0" and "Submit" at the bottom of the virtual circuit ",
Select YES for activation at the top, add VPI to 0, and add VCI to 200 (I set this according to Fuzhou Telecom and ask the local telecommunications Bureau for the specific number) "0.0.0.0" is added to both static IP addresses and subnet masks ",
Select "pppoe llc" as the encapsulation protocol"
Bridge select "DISABLED"
Add your username and password to your application at China Telecom! Don't say you don't know. I'm dizzy ..............
Enter the value you want for the disconnection interval and connect permanently when 0 is entered!
Select "AUTO" for review!
Select the automatic connection Pair Selection box!
DHCP depends on your situation! I have not set it!
The gateway keeps the default value "0.0.0.0"
Click Submit.

5. continue to the WAN interface. After selecting "1" for the virtual circuit, click Submit to enable "NO", add 0 for VCI, and add 0 for VPI, "0.0.0.0" is added to static IP addresses and subnet masks. For encapsulation protocols, select "pppoe llc" and "DISABLED" as the bridge mask. The automatic connection Vice selection box is not selected! Well, keep the default values for others! Submit at the next point, save the settings, and restart the device! This is the case until the virtual circuit is 7! I set it like this, which is troublesome. Other methods seem to be unfeasible. It seems that sometimes the webpage cannot be opened but QQ can still be used. I really don't understand why. Some people say that 6.7 can be disabled, but VCI and VPI also need to be set to 0.

6. After the device is stable, click "NAT" under the WAN, select "Dynamic NAPT" from the drop-down menu on the right, click Submit, save, and restart the device!

7. In the last step, click DNS under NAT, and then select "use aoto discovered dns servers only" as the DNS proxy on the right-side interface. If the other settings do not change, submit, save the settings, and restart the device! Here it seems that we do not recognize the use aoto discovered dns servers only and still want to see if it is. You should be able to access the Internet now! If not, you need to go to "system logs" and "diagnostic test" to see what went wrong!

2. How to set the injection ports DB108 and 102:
Now that the routing feature has been enabled for this device, but the problem has come again. I want to turn my computer into a website that allows someone else to access my computer or FTP? It's actually very easy! You can access the advanced configuration in the device. IP address: http: // 192.168.1.1/doc/index1.htm. Do you see a virtual server on it? Add the IP address you want to make the website! Even if the port is set successfully, submit and save it. At this time, your computer can be quoted. don't be busy, don't be excited. The most critical problem is that the ADSL Management port of the device and the computer port of your website are both 80, in this way, when others access your designated server, they still cannot access it. How can this problem be solved?

You need to find other configurations on the device. After you click it, you will not be able to directly see HTTP server port 80 and change it to your desired port! When you submit and save the request, you can ask someone else to access your site from the outside.

After saving the file, you cannot access your ADSL instance by using http: // 192.168.1.1! In this way, you cannot enter your ADSL device. If I change the port to 81 and want to manage it in the ADSL device later, I will only need to press http on IE: // 192.168.1.1: 81/use this port to manage your ADSL device!

1. Enter the Advanced Settings interface of Modem through 192.168.1.1/doc/index1.htm. Username: admin Password: dare
2. Go to the "virtual server" option
3. Fill in "public port" and "Private Port". (For example, if you are using a WEB server, enter 80)
4. Set "Host IP Address" to the IP address in the LAN of your server.
5. "port type" is entered based on your server (for example, "TCP" is used for WEB Services and FTP servers). For example, if the TCP port we set in BS is 16881, 16881 is entered.
6. Save settings
Note: during the test, use an Internet host to access your Internet IP address. The intranet host cannot access the Internet IP address. OK prerequisites: Use the Greenwich ADSLmodem and use the PPPOE dial-up to connect to the INTERNET.
Pppoe protocol is set on PVC 0, and the IP address of the local machine is 192.168.1.7.

Step 1: Disable the virtual circuit PVC1 ~ 7
Specifically, enter 192.168.1.1 In the IE Address Bar and the admin password greennet.
Go to the user management page
Then set the parameter-wan
Then select 1 for the virtual circuit option in the interface on the right,
Then "Submit ",
After the page is refreshed, select "no" in "enable" and "Disable" in the "bridge" option"
Click Submit"
Repeat the above process to close the other 2 ~ 7 virtual circuit;

Step 2: In the parameter settings-NAT interface, set the NAT parameter to dynamic NAPT

Step 3: In parameter settings-interface on the right of the virtual service,
Add a virtual service
First, add ID: 1, public port: 16881, Private Port: 16881, TCP, Host IP: 192.168.1.7.
Then click Set
Second, add ID: 2; Same as above, always add to 16889
Then click set to add a virtual service

The last step is to choose "Save reboot" on the parameter settings-protection restart interface.
That's all done.
If you are using a personal firewall, add the allow 16881 ~ 9tcp rules

Set port ing in ASUS 6000EV/6005HW adsl modem and click "NAT" in the main menu. There will be a "nat channel list". The settings are as follows:
Enter the following content in mupltiple port forwarding in the nat channel list:
Action: add
Channel no: 1
Protocol: tcp
Incoming port, begin: 25, end: 25
New port begin: 25, end: 25
New ip address: 192.168.1.2 Save settings
In the linksys adsl Router, set port ing and click "advanced" in the main menu. The following menu contains "forwarding". The settings are as follows:
Extport: 25 to 25
Ip address: 192.168.1.2
Click "apply.
Set port ing in the blue elf router. On the Advanced Settings page, click "Distributed Servers Setup (Virtual Serves, Virtual host settings )"
Each Virtual Server is defined as a Service Port. All accesses to this Port are redirected to the corresponding Service.
The computer corresponding to the IP address.
Service Port Service IP Enable
Email 25 192.168.1.2 √
IM 701G Emma white ADSL Modem sets port ing to go to ADSL settings, ---- Security Settings ---- advanced NAT configuration ...... add Reserved Mapping...
Add port 25 ing,
The IP address transfer type port number inside the Global IP address is as follows:
Same as the interface address 192.168.1.2 tcp 25
Save ---- restart the device
Heqin 642 Adsl Modem sets port ing. Enter telnet 192.168.1.1 in the running or MSdos window, and enter the password (default value: 1234) to enter the ZyNOS system.
Choose Menu 11.1-Remote Node Profile.
Change the "Edit Filter Sets = No" Space key to "YES" and enter the Menu 11.5-Remote Node Filter Menu.
Remove protocol filters = 6 with the Space key and press enter to save the disk. Then, return Edit Filter Sets = No, and press enter to save the disk.
Set 15. SUA Server Setup Port # IP Address in Mail Menu
---------------------
1.25 192.168.1.2
Press enter to save disk
Enter http: // 192.168.0.2/doc/setvs.htm
Generally, the default user: admin Password: 12345678 (or 123456)
Go to virtual server settings
Fill in the required ports (25) for "public port" and "Private Port)
Select "TCP" for "port type ".
Set "Host IP Address" to the Intranet IP address (192.168.1.2) of your PC ). Click "add Settings ".
Enter 192.168.0.2 In the IE address bar to go to the main interface, and click "Save settings". ADSL restarts.
Danya DB108 and 102 set port ing
Enter http: // 192.168.1.1/doc/index1.htm In the IE Address Bar
Go to virtual server settings
Add an intranet IP address and port 25
Submit and save
D-Link DI-604 port ing for Web server as an example, the LAN ip address is 192.168.0.173.
First, log on to the vro according to the instructions and click "Advanced Settings"-"virtual server"
As shown in:
 
Activation: select
Port: Select port 80
Server IP Address: 192.168.1.173
Common Internet services: WEB (80)
SCHEDULE: select any time
As shown in:
 
After you press the "execute" button, the system prompts you to restart the vro and press the "reactivate" button to make it take effect.