Ghost system prompts GHOSTERR.TXT file not found

The cause of the problem arises

Possible reason 1, download ISO is complete.

Possible reason 2, engrave battlements speed whether low-speed (10~16) correct.

Possible reason 3, what software is used to burn, with Nero engraved battlements is not good to say, his anti-piracy function is bad if the serial number is wrong, it does not make any hint of the case to let you loss is not negotiable, it is recommended to use alcohol 120% or UltraISO burn.

Possible reason 4, your optical drive read a problem.

Possible reason 5, your machine jumper, the data cable is connected correctly.

Possible reason 6, you install the restore before the format of C disk, no please format C area FAT32.

Possible reasons 7, there are inexplicable possible, the original can be installed to restore the disc will not be able to use the GHOSTERR.TXT would appear, but ignore it on one side over the period of time to use the discovery can be, hehe, may be a ghost.

Ghost occurs when A:ghosterr. TXT Solution

Use the format C area to see, sometimes unexpected effect.

(1) ISO file is correct;

(2) Optical drive performance, optical disc quality;

(3) Ghost version;

(4) hard disk problem (good solution, rewrite the boot sector of the hard disk reformat, into the pure DOS:FDISK/MBR again: Format C:).

A:ghosterr has not been resolved while restoring the ghost system. TXT,

It's time to consider whether there is a problem with the memory. Patronize many forums, but it has been mentioned from the end. The motherboard and memory also have cause and effect (memory is incompatible with the motherboard). Multiple motherboards that occur on the old Lntel chipset. such as: Lntel BX 810e 810e2 815e 815EP 815ept is especially equipped with more than one memory, it is easier to occur when the recovery ghost system occurs a:ghosterr. TXT phenomenon. The reason is that the memory is not compatible with the motherboard because the Lntel chipset motherboard only provides 4 BANK,DIMM2/3 common two bank

Final Solution: (Please test!)

(1) not exceeding 512M;

(2) using more than two memory, preferably the same brand. Memory of the same specification (excluding capacity);

(3) To use three memory, to ensure that the DIMM2/DIMM3 slots are used on a single side of memory, that is, not more than 4 sides of the bank;

(4) Try not to overclocking.

(5) Changed the quality of good memory;

(6) The memory has changed the slot.

Memory not compatible with motherboard

Causes:

1.iso download is not complete, no matter what way to download must verify MD5 code

2. Burner burning quality is not good or burning disk quality problems, burning to use less than 24x end burning

3. CD-ROM drive performance problems during installation

4.ghost Vibration chassis and other external factors, the general reinstall is good

5. The biggest factor is the super engraving, so more than 700m of disk is very dangerous, almost all of these problems will occur.

Because the ISO gho file is a high compression ghost file, the entire file up to 650m, if the above factors such as the impact will stop halfway or the first startup failure or the system individual files are missing. Please check the solution once. If you have the ability to decompress the ISO or use D-tools to isolate, and then restore to C with ghost8.0, speed and success rate are very high. It is also possible that many people may have encountered this situation: the original C disk has errors, need to scan or tidy up. Gho files to extract the same, it is best to use a virtual optical drive such as Daemon-tool, and then copy it out. There is a mistake, then try again. In short, try to ensure that Gho file integrity.

Reason: Three possible--a, the mirrored file itself is corrupted (it may be corrupted when data is transferred during downloading, or it may be corrupted by data write errors) b, CD-ROM bad results in optical drive read disk (may be burning failure or the quality of the disc itself) C, ghost version is too low to cause the mirror can not use ( Please do not use the version below Ghost 8.0, especially the 7.5 edition. Version 2003 may be possible, but it is advisable to use version 8.0. The ghost version in the mirror is 8.0 version. )

Solution: A, download again. b, re-burn in a better quality disc and ensure the success of the burn. C, use Ghost version 8.0

When using ghost, try not to overclocking.

1, Ghost Time to jump out of a dialog box ~ said to find a file called GHOSTERR.TXT ~ "

Solution: To ensure that CD-ROM slow burning, with PQ or format c:/u C disk format, the proposed FAT32 format. Sometimes not formatted, repeat cloning 2-3 times to succeed.

2. What happens if I/O errors occur?

The primary reason for this problem is the problem with the IMG floppy image file. If you want to use the file cloning system on the CD, only manual this trick. Start the MSDOS7.1 on the CD, make menu 2 dos-real mode, then go to the Ezbootghost directory on the disc, start Ghost 8.0, and then clone the Gho file in the root of the disc to your target partition.

3, power management mode is not correct, how to modify?

• If you see that the Power management mode that is displayed is incorrect during the installation process, you can also change it. (usually by computer automatic judgment)

• If you can enter the system, then in C:Program files have procedures can be changed, run Autosethal.cmd

• If the system is not accessible, modify the tools on the disc.

4. What are the types of power management modes?

ACPI Multiprocessor PC

Generally used in 2003 after the purchase of computers, WIN2000-2003 support this mode of power. ACPI multiprocessor motherboard for installing multiple processors, dual-processor computer in ACPI mode (dual-processor motherboard support), motherboard support HT (Hyper-threading) and motherboard with HT CPU installed/Early entry-level dual CPU motherboard with dual CPU installed/ Entry-level servers and a small number of departmental-level servers, such as Intel 845GE L 845PE, 865PE above and using P4 x.x HT cpu,2004, are more common.

MPS Multiprocessor PC

Dual processor computer in MPS multiprocessor PC:APM mode (motherboard supports dual processor)

Win2000 WinXP Win2003 are supported. Please check the motherboard or computer instructions and choose carefully.

Compaq SystemPro Multiprocessor or 100% compatible

Compaq SystemPro Multiprocessor or 100% compatible rarely seen, oh, do not know how to write the description of

Win2000 WinXP Support, does not apply to Win2003.

ACPI uniprocessor PC

Generally used in 2003 after the purchase of high-end computers, WIN2000-2003 support this power mode. An ACPI multiprocessor motherboard for installing a processor, a dual-processor computer in ACPI mode (dual processors are not supported on the motherboard), or a single-processor computer in ACPI mode, and the motherboard provides APIC functionality, such as SIS 748/Most Intel 845 series/via Kt600/ NVIDIA nFORCE2 or newer products, generally 2003 years after the machine uses this mode.

MPS uniprocessor PC

Dual-processor computers in MPS single PROCESSOR:APM mode (motherboards support dual processors) or single processor PCs in APM mode, motherboards provide APIC functionality Win2000 WinXP Win2003 are supported. Please check the motherboard or computer instructions and choose carefully.

Advanced Configuration and Power Interface [ACPI] PC [Default]

Typically used for computers purchased 2003 years ago, the most common type, win2000-2003, is supported by ACPI for single processor motherboards with single processor ACPI systems, single processor PCs in ACPI mode, and motherboard does not provide APIC functionality. If you select this startup to discover that the cursor in the upper left corner does not go into the system, open ACPI in the BIOS. Motherboard chips higher than BX440 or equal to the Intel 815/sis 735/nforce1/ali/via Kt400/via p4x266 and so on, generally 2003 before the machine support this mode.

Standard PC

Standard PCs are common to any standard PC, non-ACPI, or non-MPs, enabling 386, 486, PENTIUM2 350, or other types of machines;

All systems are supported, but the new motherboard is ACPI-enabled and has open ACPI for a new motherboard using this may cause a soft shutdown!

There is also another:

Silicon Graphics Visual Workstation

Silicon Graphics Visual Workstation

It's rare, only Win2000 supports it.

815 the motherboard has compatibility issues with modern memory strips:

Recently, because of the low memory, many users have purchased a memory bar to upgrade. Many of these users have motherboards that use a 815E or 815EP chipset and are buying modern memory strips. As you can imagine, 815 chipset of the motherboard in the modern memory, if the two-sided memory, can only support one, if the single side of the memory bar, you may support more than two (of course, up to 512 trillion). In this way, many users buy two-sided memory home, there are a lot of problems, Light automatically quit the game, the heavy blue screen, or even panic. Anyway, there is no reason to change a number of memory can not solve the problem, even many businesses do not know that there is such a problem, so in the sale of memory, you will not ask what the motherboard you use.

Of course, this issue on other brands of memory may also have the same situation, I did not try, so do not dare to open the verdict, however, the modern memory and 815 motherboard compatibility between the problem is certain

Memory is one of the core components of the computer, its role is self-evident, while memory is also a major source of computer failure. Based on its importance, the consequences of memory failure can not be overlooked, here to analyze a few typical memory failures, hoping to learn to solve the memory failure of ideas and methods.

1. Poor memory quality causes Windows to install error

Fault phenomenon: A new assembly of compatible machine, configured for PENTIUM4 1.8A, i845g motherboard, the motley Hy 256MB DDR266 memory, Seagate cool Fish 5 generation 60GB hard disk. After the hard disk is installed Windows 98, copy system files during the installation of the Times wrong, press "Cancel" can be skipped after the error to continue the installation, but again later, Windows installation can not be completed. Due to the failure occurred during the system file copy phase, the initial suspicion is that the CD-ROM problem, format the hard drive and replace the Windows 98 CD to reinstall, the failure remains. Fault suspect transferred to the hard disk and memory, after replacing the hard drive, the failure still exists, eliminate the hard drive, replace the memory after the failure disappeared, the final confirmation of the cause of Windows installation error is inferior memory.

Failure Analysis: Windows installation process needs to copy files from the CD to the hard disk, and memory as a transit point for system data exchange, played an extremely important role in this process. This example is a poor memory quality and does not stabilize the operation and causes system file replication errors. Because memory has a very important position, its quality can not be ignored, the use of inferior memory or even unable to complete the installation of the operating system, not to say, in the use of a variety of difficult and incurable diseases, it is recommended to try to buy high-quality brand memory.

2. The Registry frequently error trouble memory

Failure phenomenon: A computer configured for pentiumⅲ550 (overclocking to 731MHz), SiS630 motherboard, a motley Hy 192MB (128MB+64MB) SDRAM memory. More than a year after the system became unstable, often after the boot into Windows, the registry error occurred, need to restore the registry. Initially thought that the operating system is unstable, the format of the hard disk after the problem has not been thoroughly resolved, or even become more serious, and sometimes even appear "Windows Protection Error." Because the CPU has been operating in overclocking, the initial suspicion of the fault originated from the cpu,cpu down the frequency of the registry error significantly reduced, more suspicious of the fault caused by the CPU, deliberately replaced the CPU, but the fault has not disappeared, still appear. To completely troubleshoot the problem, use the substitution method to test, finally found that the culprit is the 64MB of memory.

Fault Analysis: The machine is in the overclocking state for a long time, CPU and memory clock frequency are 133MHz. That 64MB of memory is hy-7k chip, work is also poor, the long-term operation under the 133MHz finally overwhelmed, resulting in frequent errors in the registry. Some poor workmanship, low parameters of memory may be in a period of time overclocking work, but in the long run will often occur problems, causing system failures, this is the user should be the idea of the problem.

3.Remarku memory causes the computer to not boot

Symptom: A computer is configured to PENTIUMⅢ800EB, VIA 694X motherboard, HY 128MB PC133 memory. Added a 128MB of the motley Hy PC133 memory after the monitor black screen, the computer does not boot normally, unplug the memory after the failure disappeared. After inspection, found that the new memory bar is not a problem, in other machines can be used normally, but can only work under the 100MHz FSB, can not be used under 133MHz. To use this memory, it was later forced to set the -33mhz asynchronous mode in the BIOS's memory settings.

Failure Analysis: The memory chip number marked-75, should be PC133 memory, but the handwriting on the chip is more blurred, most likely from -7k or -7j memory remark, naturally can not work under 133MHz. According to this, consumers in the purchase of memory should be careful to beware of JS, to prevent the purchase of remark memory.

4. Memory slot dust causes memory not to work properly

Failure phenomenon: A computer suddenly can not start normally, the speaker issued a long three short alarm sound, according to experience to determine the problem in memory. The machine inspection found that the memory strips did not burn the signs, to get other machines can also be used normally. After cleaning the motherboard to plug in the memory, the above failure disappeared, the final confirmation of the cause of the memory bar is not working properly due to the memory slot accumulated dust too much.

Fault Analysis: The computer is a very sophisticated machine, even small dust may cause it can not work, so in the use of computer should pay attention to keep the surrounding environment clean, usually do a good job of cleaning computer parts.

5. Incompatible memory causes capacity not to be properly identified

Symptom: A brand-name machine, configured for pentiumⅲ800, I815E motherboard, HY 128MB memory, then added a Hitachi 128MB memory, but the motherboard recognized total memory capacity of 128MB. After testing, on this computer, two memory can be used separately, but together with the recognition of 128MB, we know that these two memory compatibility problems, and later replaced the newly added memory to use HY chip memory after the fault is resolved.

Failure Analysis: Due to the difference in electrical performance, there may be compatibility between the memory strips, the problem in different brands of memory in the context of the occurrence of a greater probability. Therefore, the use of two or more than two of the memory bar should choose the same brand and model of products, so as to maximize the avoidance of incompatible memory. If you cannot purchase a product that is the same as the original memory, should try to use the market reputation better brand memory, they generally have been nearly million system of special matching and compatibility testing, components, design and quality can also meet or exceed industry standards; In addition, the product testing procedures are also better, thus ensuring its reliability, Consistency and compatibility. It should be explained here that not all brand memory has good compatibility.

6. Chipset is incompatible with memory

Failure phenomenon: In a famous brand i815 motherboard, a hy 512MB PC133 memory can not be correctly recognized, only 256MB, even if the replacement of other brands of memory failure is still.

Failure Analysis: There is an incompatibility between memory and the chipset and memory may also be incompatible. Intel's 815-series chipset supports a single memory with a maximum capacity of 256MB and does not support individual 512MB of memory. These are innate flaws in the chipset that cannot be resolved, and what we can do is to avoid using such a large amount of memory on such chipsets.

7. Motherboard is incompatible with memory

Failure phenomenon: K7 era, in gigabyte 7IX motherboard using a single memory, must not plug in the DIMM2, otherwise installed Windows 98 o'clock will appear blue screen. If you want to install two memory, generally can only use DIMM1, DIMM3, as long as it involves DIMM2, the problem will appear. In the near future, there are also rumors of Kingston granule DDR333 256MB Memory and NFORCE2 IGPV chipset compatibility issues, there will be automatic restart, crash and other failures.

Failure Analysis: Although memory and motherboards have done a great deal of compatibility testing prior to listing, there is a potential for compatibility issues between the number of computer hardware products and the extraordinary speed of updates, although the odds are quite small. For motherboard and memory compatibility issues, there is no good solution, generally only choose to replace the memory or motherboard.