History of the most comprehensive Buffalo whr-g300n CH v2 Brush OpenWrt Tutorial

Buffalo whr-g300n CH v2 Brush OpenWrt, there are two ways, one is windows under the brush, one is to use the TFTP brush under Linux,
Buffalo Whr-g300n-ch V2 's OpenWrt firmware at this address download:

http://downloads.openwrt.org/snapshots/trunk/ar71xx/
OpenWrt official support for g300n v2 is sometimes no, there is no formal support,
Due to the same hardware, we can download firmware using whr-g301n or whr-hp-g300n,
And these two routes have not been formally supported by OpenWrt,
OpenWrt each time the OpenWrt firmware of g301n and hp-g300n is released, and each time it is released, the firmware will be openwrt to cancel the download,
So http://downloads.openwrt.org/snapshots/trunk/ar71xx/this link occasionally will have the corresponding firmware download,

In order to provide convenience, here I provide download,
Version Squashfs-factory
Version Squashfs-sysupgrade
Version Squashfs-tftp
Kernel 3.2.6

Say in advance, this route is not dead, in any case can be used under the Linux TFTP brush back,
Ⅰ.windows under:
We need to use two tools,
1.HFS (click here to download HFS)
2.Telnet
Windows7 does not turn on the Telnet function by default, here is the way to tell how Telnet is turned on,
Control Panel-Programs-programs and features-turn Windows features on or off,
The Telnet server and Telnet client are checked, determined,


Download the Sysupgrade version of the firmware provided above,
Use HFS mount, Mount method:
｛
Mount Method:
①. Open HFS,
Menu-ip Adress, select your route to your computer's assigned IP address,
(Generally 192.168.1.? , my 192.168.36.2 in the picture)

Drag the firmware package to the left under "Virtual File System" and become this:

telnet or SSH login route, enter the following command:

cd/tmp
Wget http://192.168.1.109/openwrt-ar71xx-generic-whr-g301n-squashfs-sysupgrade.bin here to hint, ①. The firmware name can be changed to "1. Bin "re-mount, the command here can be abbreviated, ②. Here the 192.168.1.109 should be changed to the native IP, like, I should be changed to 192.168.36.2,
Mtd-e linux-r write Openwrt-ar71xx-generic-whr-g301n-squashfs-sysupgrade.bin linux

(attached firmware renamed Rookie command:

cd/tmp
wget Http://192.168.1.109/1.bin
Mtd-e linux-r write 1.bin linux

）

Wait for the screen to show that after losing the host connection,
Wait 1 minutes, to power and router lit, indicating the success of the brush, the following I am Linux under the brush routing tutorial, brush well after the configuration page can not open I will be in another article detailed description,
http://zzsjlove.diandian.com/2012/04/whr-g300n-v2-openwrt-luci/

Ⅱ.linux (take Ubuntu as an example):
Download the TFTP version of the firmware (download provided above),
It is also recommended to change the firmware name to 1.bin
Put the firmware into Ubuntu home folder (home),
First Ubuntu networking, how to network I will not repeat,
Installing TFTP
In the terminal, enter:

sudo apt-get update
sudo apt-get install TFTP

Enter in the terminal

ifconfig

Check your network card which is the local network card, if it is a virtual machine user to see which is the connection between the virtual machine and the host network card, which is directly connected to the router network card,
Connect a computer network port with a routed LAN port with a network cable,
In Terminal input:

sudo service networking stop Ubuntu 9.10 users with this command,
sudo service Network-manager stop Ubuntu 10.4 or above system with this command,

sudo ifconfig eth0 192.168.11.2 must be this IP segment, even if you have changed the IP of the route, here you still have to configure the local network adapter for 192.168.11. , Eth0 is the local network card, mentioned above to pay attention to,
sudo ifconfig eth0 netmask 255.255.255.0 (This step can be omitted)
sudo arp-s 192.168.11.1 aabbccddee5f ' Aabbccddeeff ' changes to your router MAC address (labeled on the back of router), can be added with colons

,

Unplug the routing power,
In the terminal input

Tftp
tftp> verbose
Tip verbose mode on.
tftp> binary
Prompts mode set to octet.
Tftp> Trace
Tip Packet tracing on.
Tftp> REXMT 1
Tftp> Timeout 60
Tftp> Connect 192.168.11.1
Tftp> put 1.bin

Immediately plug in the router power, waiting for Ubuntu display is pushing the firmware, and then push the completion, will wait for input,
Input

quit

Exit TFTP
Input

Exit

Exit terminal,
Wait for the route restart to complete, power and router, brush completion,
After the brush machine in the browser input 192.168.1.1 does not open normally, I will in another article detailed explanation,
http://zzsjlove.diandian.com/2012/04/whr-g300n-v2-openwrt-luci/

Ps:ubuntu the method of TFTP brush routing can be brushed back to the official firmware,
PS:OPENWRT Brush back to the official only with TFTP method, and OpenWrt under the brush back DD-WRT can use this firmware:
Whr-g300nv2-openwrt-to-dd.bin
Use this firmware to upgrade the OP page to DD,
After you brush to DD, it is recommended that you reset it once, or then brush the updated version of DD.

History of the most comprehensive Buffalo whr-g300n CH v2 Brush OpenWrt Tutorial