Home Router installation instructions

After reading the Home Router installation instructions, you will have a comprehensive understanding of the installation of home routers. In subsequent articles, I will give a detailed introduction to hardware installation and PC settings. Do not worry, but all problems will be solved.

Home Router installation instructions

The simplest configuration for using a Broadband Router to access the Internet is: a PC with a 10/100 M Ethernet NIC, a broadband access line that you have applied for and activated from the carrier, and a Broadband Router. Make sure that your PC can access the Internet through the NIC. Now, you can refer to this Guide to quickly configure a Broadband Router.

I. Home Router installation instructions: hardware Installation

1. Unpack the package of the Broadband Router, remove the power cord of the Broadband Router and power adapter), and place the Broadband Router on the desktop plane. Connect the power outlet and the Broadband Router with the power adapter power cord. At this time, you can see that the indicator light on the front of the Broadband Router is in the order of "LAN1 "~ "LAN4" and "WAN" are completely bright for about half a second and then off → "M1" is on for 2 seconds and then off → "M2" flashes. At this point, the Broadband Router is successfully initialized and can be used normally. If this is not the case, check your power supply or call our technical support staff.

2. connect to a Broadband Router, PC, and broadband access line.

1) if you are using xDSL or Cable to access the Internet, use the following methods to connect the Internet, connect the telephone line to the adsl modem, connect the adsl modem to the WAN port of the router, and connect any LAN port to the computer, cable MODEM is connected to the WAN port of the router, and any LAN port is connected to the computer. After the connection, start the PC and xDSL/Cable Modem. You can see that the indicator corresponding to the connection port of the Broadband Router and xDSL/Cable Modem is on, and the indicator of the PC Nic is also on. Make sure that Modem is the default factory settings.

2) if you are using Ethernet Access, connect to the WAN port of the router using the twisted pair ethernet cable and connect to the computer using any LAN port. After the connection, start the PC. You can see that the indicator light corresponding to the connection port of the Broadband Router is on, and the indicator light of the PC Nic is also on.

Ii. Home Router installation instructions: PC settings

1. If you are using a Windows 95/98 Operating System

After entering the operating system, click "start"> "Settings"> "Control Panel" on the taskbar and double-click the "network" icon. The following page is displayed: select the "TCP/IP" attribute on the "configuration" page. You may see more than one "TCP/IP". Select "TCP/IP" for the NIC connecting to the Broadband Router ". The property page is as follows: Fill in IP address 192.168.1.2 on the "ip address" Page, subnet mask 255.255.0, and "Gateway" page in the gateway 192.168.1.1. Click "OK" on the page and "OK" on the "Network Properties" page to restart the PC as prompted.

2. If you are using a Windows 2000/XP operating system

After entering the operating system, click "start"> "Settings"> "Control Panel" on the taskbar and double-click the "Network and dial-up connections" icon, then select the "local connection" corresponding to the NIC connecting to the Broadband Router. You will see the following interface: Select "properties"> "general"> "Internet protocol TCP/IP )", view its "properties". On the following page, enter the IP address 192.168.1.2 and the subnet mask 255.255.255.0. The default network is 192.168.1.1. Click "OK" on the page and "OK" on the "Local Connection Properties" page ". Wait until the system configuration is complete. Note: Fill in the local DNS server address in "Use the following DNS server address.

3. If you are using the VISTA system:

In Windows VISTA, the network parameter configuration process is as follows: Enable "Network Neighbor"-"Local Connection"-"view status"-"Internet Protocol Version 4"-"attribute": Now, you can log on to the Broadband Router!

Iii. Home Router installation instructions: Broadband Router settings

Open the IE browser and select "Tools"> "Internet Options"> "connection"> "LAN Settings" in the menu bar. please press "√" before "Automatic Detection Settings" on this page ", however, do not set "√" in the "use automatic configuration script" and "Proxy Server" sections ". Click "OK" to return to IE. Enter 192.168.1.1 in the address bar and press Enter. In the displayed dialog box, enter the username "admin" and password "admin". Click OK to log on to the Broadband Router. After logging on, the "Setup Wizard" will pop up. Follow the wizard prompts to configure a Broadband Router. Click "Next" → select your Internet access method:

1. If you are using ADSL dial-up Internet access, select "ADSL virtual dialing PPPoE" and click "Next ", fill in the internet account and password provided by the carrier to you. Note the case sensitivity.) Click "Next" and "finish". The current default dialing method is "On-Demand connection". If you need to change it, see User Manual). Then, select "running status" in the tree menu on the left of the Broadband Router configuration interface, and click "Connect" in the refreshed right window, you will see that the Broadband Router has two IP addresses, subnet mask, gateway, and DNS server ). Now, go to the PC's "TCP/IP properties" page, enter the DNS server address obtained by the Broadband Router in the DNS properties page. On the Windows 95/98 page, enter the DNS server address and click "add".) confirm your change. Now, you can use your PC to access the Internet.

2. If you are using a Cable Modem or an Ethernet bandwidth Dynamic IP address, select "Ethernet bandwidth to automatically obtain the IP address dynamic IP address from the network service provider )", click "Next" to complete the configuration of the Home Router installation instructions. At this time, you can see in the "running status" that the Broadband Router has obtained the IP address provided by the carrier and other information. Similarly, you also need to fill in the allocated DNS server with your PC method reference 1), then you can use your PC to access the Internet.

3. If you are using an Ethernet broadband fixed IP address, select "Ethernet broadband, static IP address provided by the network service provider)" and click "Next ", enter the IP address, subnet mask, gateway, DNS server, and backup DNS server that the carrier has allocated to you. Click "Next" to complete the settings. Similarly, you need to enter the DNS server assigned to you by the carrier in your PC method (refer to 1). Then, you can use your PC to access the Internet.