How do Dell Dell laptops set up to boot from U disk?

First you plug the USB boot disk into the Dell notebook interface, and then you can set up the Dell notebook USB drive with the following two ways.

Method one, traditional law

Set up the computer USB disk boot, the traditional way is to enter the computer BIOS settings, and then enter the boot startup settings, then the USB device as the first boot, and then save, the following is the specific steps:

1, restart the Dell notebook, in the notebook logo screen, immediately press the keyboard "F2 key" to enter the notebook BIOS settings, as shown in the following figure:

Note: The F2 setup and F12 Boot options prompts are available at the bottom of the Dell notebook boot sign interface, where we press the F2 key to enter the BIOS setup.

2, after entering the BIOS setup, we use the → Key on the keyboard, switch to the top menu in the "Boot" menu, and then select "USB Storage Device" as the first start item, select, Entel key confirmation, and finally press F10 key to save, then will prompt you to save , we check "Yes" and press ENTER to confirm it, then the Dell notebook will automatically restart, then you can enter the USB disk to start the interface.

Supplementary Note:

In the boot into the logo screen, immediately press the key to the upper left corner of the keyboard, you can enter the BIOS main interface, generally in the logo screen, in the lower right of the screen will have access to the BIOS key prompts, if you do not remember or do not know, take a look at it.

Just enter the BIOS, the default is main this item, here is mainly to set the time, and some hardware display, we do not move the inside of the option.

We have to go through the left and right arrow keys, choose the boot of this item, boot for the "start" meaning, here is to set up a U disk or CD-ROM where to start.

If you want to boot from the U disk, select the USB Storage Device, use the arrow keys to move to this item, and then use the + + key, move this item to the top, and then press ENTER to determine.

If you want to boot from the CD, select Cd/dvd/cd-rw Drive, move to this item with the UP and DOWN ARROW keys, and then use the + + key to move the item to the top, and then press ENTER to determine.

If the system is installed, to restore the original hard drive, you must choose hard Drive, the same with the arrow keys to move to this item, and then with the + + key, move this item to the top, and then press ENTER key to determine.

The reason to move to the top is, which is the top, which is the first boot, move to the boot Priority order this item is OK, this is the title, Chinese meaning is "Start sequence settings."

After setting, press F10 to save and exit, restart the computer can be from a U disk or CD-ROM boot, if the computer in PE does not see the hard disk, that is the hard drive mode settings are not correct, it is necessary to re-enter the BIOS, the hard disk mode settings, the following on the hard disk mode setting method for explanation.

Set the hard drive mode, go to the BIOS main interface, move the cursor to the advanced, advanced for the advanced setting meaning.

After entering the advanced, select SATA uperation, which means "SATA mode" and press ENTER to enter its subkeys.

Select ATA in the Small open window and press ENTER to determine, because, in particular, some of the older PE systems are incompatible with the Achi mode, so to start the traditional ATA mode, if it is some newer PE system, they can be compatible with Achi mode.

Of course, the final step is to save all settings, usually to the exit item under the option to save & exit Setup, Chinese meaning "Exit and save Settings", there is a direct way, is to press the F10 key, the F10 key is all computer generic " Exit and exit the key ", press it on it, the entire BIOS from the U disk or CD Boot set up."

Method Two, shortcut key method

Different brand notebook computers have different startup key shortcuts, and the boot key shortcut for Dell Notebooks is F12, using the following methods:

The same is in the computer restart or boot into the logo interface, we immediately press the F12 key on the keyboard, and then enter the following shortcut to set up the interface, where we directly select the second "USB Storage Device" (Some direct display inserted notebook USB disk name, Always contains the word "USB", selected, we directly press ENTER (enter), then you can enter the USB disk to start the interface.

If you want to start from the CD, choose CD/DVD/CD-RW Drive This item, and then press ENTER, you can start immediately from the CD, of course, you have to put the system in the CD drive first, so the quick Start method is explained.

Dell notebook How to set up a USB drive method for everyone to introduce here, we recommend that the priority to adopt method two, so more convenient and fast.

Attention matters

Because the BIOS version is different, it may vary in the Startup settings option, but it will generally be the same, please use it flexibly.

Before installing the system or setting the BIOS, it is best to detect the compatibility of U disk and computer so as to avoid unnecessary trouble.