How does the wireless router realize the mobile Internet?

One, the connection of the line. Several of our common dial-up networking connections are as follows:

①: A broadband network of "ADSL Cats". For example, directly from the telecommunications, unicom and other operators to connect the telephone line in the household network, with "cats." The following figure:

②: There is "light cat" optical fiber network cable households. Use the following figure:

③: No "light cat" network cable households. The following figure:

④: "Community broadband dial-up" network. The following figure:

Note: From the above four schemes, although the access Network (household network) is different, but have a common feature: that is all need to point "broadband connection", the computer can surf the Internet.

The WiFi led on the router flashes (approximately 1 seconds blinking once) after the power supply has been plugged into the MP01. When the network cable access, the router on the WLAN indicates whether there is light or flashing, if not bright, it means that the line is not, please reconnect the network line or replace the network cable or redo Crystal head. LED status and mode selection instructions are shown below:

Second, wireless connection. Mobile phone wirelessly connected to the mp01/02. (including Android phone, Apple system phone configuration, detailed below)

①, from the "Settings" item of the mobile phone menu, opens the wireless WiFi setting in the mobile phone and goes to the wireless search list. The following figure:

②, find the SSID to connect to (for example, the B-LINK-MP02 in this example) and connect to it. The following figure:

③, the status of the successful connection, as shown in the following illustration:

Third, check the phone connection, get the IP address is correct. (including Android phone, Apple system phone, detailed below)

(Fourth step can be done only if the IP address of the mp01/02 192.168.16.X is obtained correctly)

Android System: Click on the Connected SSID (MP02 in this example), it will appear the following map IP address information;

Four, log on to the Router Web page.

①, find the mobile phone system with the browser, (here must find the system from the browsing, such as UC, QQ, 360, Baidu and other browsers, many are logged out of the Web Administration page), as shown in the following picture:

②, open the system with its own browser, enter the login IP (that is, the router's gateway, the default gateway is 192.168.16.254), as shown in the following figure:

③, enter login username and password, default is "admin", lowercase letter. As shown in the following illustration:

V. Set up the router.

(Mobile phone login to the router's Web page, and computer login is exactly the same, because the phone screen is limited, screenshots relatively small, not easy to explain.) The following is a screenshot of the computer to facilitate your operation.

"Network Settings"-"wan" found, in WAN mode, select ADSL virtual dial-up (PPPOE), in the following fill in their own broadband Internet account and password (that is, the original computer when the Internet "broadband connection" in the username and password), here must be filled in correctly, otherwise, the router can not dial the number. The following figure:

Tip: "ADLs virtual dialing" or "PPPOE" in a router is equivalent to a "broadband connection" in your computer, these are a means that the router "PPPOE" = "broadband connection" in the computer, the difference is that the computer "broadband connection" needs to manually go to the point, and the router in this, is to pass the electricity ( Automatically connect on the line when it is connected properly.

Six, the wireless password setting.

Find "Wireless Settings"-"Security settings", Safe Mode Select "Wpa2-psk", WPA algorithm Select "AES", the password between 8-15 bits (password is too long, in the wireless connection error prone), set up, point "Restart routing" for the router to take effect. The following figure:

(Note: When the point "restart Routing", indicating that the current router is rebooting in effect, wireless must be disconnected, just wait 1 minutes after the wireless search again, and enter the set wireless password, reconnect)

Note: The WAN IP information obtained here is dynamic, as long as there is access to IP information can be, regardless of how much. If you do not have wide area IP information, check the correctness of the Internet account number and password that are filled in PPPoE