How to clear the laptop keyboard -- Toshiba pr100

Label: Computer Skills

Last Update Time: 2010-02-05 08:59:37

I don't know why the Shift key of this book is always in the press state, so that the sticky key is started, and I didn't actually press it. After cleaning, the main steps are illustrated below.

Main tools: One-minute table batch, small brush, anhydrous alcohol, soft cloth.

1. Remove the record

As shown in, each of the lower and right sides of the axis connecting the base and the screen has a concave area. With a batch of loggings, the two sides gradually slide up from the middle to remove the long bars. Is what it looks like after the button is removed:

2. Remove the keyboard

(1) Remove the two screws shown in the Red Circle

(2) Remove the screws on the back of the book as shown in

(3) gently pull forward the keyboard and pull out all the clips that are stuck under the base, such:

(4) Be careful when removing the keyboard. There are cables connected to the Base (in red circles). Put down the keyboard in turn like this.

3. Remove the keyboard Cable

To remove the keyboard cable, just push the black clips in the red circles to the palm tray.

Look, the clip on this side has been pushed away:

After both sides are pushed away, press the keyboard cables below to easily remove them, as shown in. Note that the starting point in the figure is only required for shooting. You can use your finger to remove the cable When disassembling it.

It is the keyboard outlet after removing the cable. Check that the black cards on both sides are in the available status.

Is to remove the base of the keyboard

Is the entire removed keyboard.

Is the full back of the removed keyboard

4. Remove the keycaps and clear them.

(1) the method for obtaining the keycap is to press the top edge of the keycap and press it up to the bottom edge of the keycap, and then the keycap will jump up, like this:

(2) then, shake the key cap slightly to the left and right, and shake the small bulge of the key cap hanging on the x-frame to easily remove the entire key cap. If you just want to clear some keycaps, you can also remove them. In this way, clear dust in the keyboard directly:

(3) note that there are metal hooks under some long keys (six in total: bksp, enter, shift (two), Ctrl, space, when getting the upper end, remove the metal hook outward with a bell table batch, and then remove the upper end, as shown in:

In addition, when you take the Space key, you should note that there are three links in it when you take the lower end. First, place the middle of the link, and then split the left and right sides in sequence. Just click it; use the above method to retrieve the upper part.

(4) If the keyboard is dirty, it is best to take down all the keycaps, set them in order, and clean them completely. The keyboard is split into a row of keycaps, and the rubber bowl in the keycaps is put in the cup.

(5) Note that the top and bottom of the four key caps (F, J, lead, →) are the opposite, first roll it up and then shake it down,Otherwise, it is easy to break the key cap.. The result is all split, the top rubber bowl, the rubber bowl under the six key caps in the bottom right corner, and the rubber bowl under all the key caps are respectively placed in the three small caps.

Is the keyboard for removing the keycaps

(6) carefully clean the front and back of the removed keycaps, rubber bowl, and keyboard base with a skin tiger, a small brush, and glasses cloth dipped in anhydrous alcohol without leaving any dead corners. This has a considerable workload and requires mental preparation.

5. Install the keycaps

(1) When the keyboard base, keycaps, and rubber bowl are completely dry, install the keycaps one by one. When installing the software, first place the blue rubber bowl (the big data rushed down and smoothly placed at the bottom of the X-bracket, as shown in), and then click the upper part of the key cap (you can hear the click ), then press the lower part of the keycap. In fact, the order is the opposite of the Order of the key cap. After the installation, press the key. If you feel bad, it may be because the rubber bowl is out of order, and then you can try again.

(2) Pay attention to the Keys (as shown in red circles) that are opposite to the upper and lower keys of other key caps. The installation sequence is also the opposite. You need to install them first and then install them.

(3) In addition, as shown in the blue circle, you should also pay attention to the method when pressing the two ends of the Space key. In short, you must first press the one end of two small tentacles, and then press the other end. In fact, as long as you carefully observe the relationship between the two tentacles on the x-stand and the four dots on the two holes and the key cap, you will understand the truth (such ).

(4) In addition, do not panic when installing a keycaps with metal hooks. First, put the metal hook in the small hole of the keyboard base as shown in red circles; then, use the shaft as the axis and keep the metal hook in the hole, and slowly put down the key cap; then, press the top and the bottom as the normal keycaps do. After the installation, if the button feels very dead and there is no elasticity, It is the metal hook slip, then it will be pulled and re-installed.

(5) Reload the cables, buckles, and screws on the keyboard in sequence.

6. Miscellaneous

After this is done, it is best to buy a keyboard film to save the trouble of cleaning in the future (about 2 hours ).