How to connect the Mercury mw3030r wireless router

the connection method of Mercury (MERCURY) mw3030r wireless router

1, Login MW309 Settings interface:

In the browser's address bar, enter: melogin.cn and press ENTER (enter) key--> in the jump page, will be prompted to set "Administrator Password" (is the login password), the user set their own. (If not open melogin.cn page, please read the article: melogin.cn can not open the solution)

Input in Browser: melogin.cn

The first time you open the MW3030R router Settings page, you are prompted to set the Administrator password

Note the problem:

(1), please take good care of just set up the "Administrator password", the time to log in, you must enter just set the administrator password before you can log in. If you forget the administrator password, you can only restore the router to factory settings, and then reset the administrator password.

(2), if your router has previously set the "Administrator password", then enter in the browser: melogin.cn, will prompt the user to enter the "Administrator Password", as shown in the following figure; At this time, please enter the Administrator password set before login.

When you open the MW3030R settings interface again later, you need to enter the administrator password for the settings login

2. Run Setup Wizard:

After entering the Setup interface, the system will automatically pop up to the Setup wizard interface, if it does not eject, the user can click the Setup Wizard option on the left menu to enable it.

On the MW3030R Settings page, run the Setup Wizard

3. Choose the way of Internet:

(1), if you have a broadband account, broadband password, and when not using the router, the computer needs to use the "broadband connection" (or similar dialing procedures), fill in the broadband account, password, dial-up before the Internet. When you set up the Mercury mw3030r router, you should choose "PPPoE dial" this way of surfing the Internet.

Select "PPPOE (ADSL virtual dial)"--> "Next".

Select "PPPOE (ADSL virtual dial)" This way of surfing the internet

"Online Account" fill in: Broadband account--> "Access password" fill: broadband password--> "next".

Set up PPPoE dial-up broadband account, broadband password

(2), if you do not have a broadband account, broadband password, and in the absence of the use of routers, the only need to set the computer IP address for automatic access, and then connect the broadband network cable to the computer's network interface, the computer can be online. When setting up the Mercury mw3030r router to surf the Internet, you should choose: Dynamic IP.

Select "Dynamic IP" in Internet mode

(3), if you do not have a broadband account, broadband password, but the broadband operator (network administrator) gives you IP address, subnet mask, Gateway, DNS, and in the case of not using a router, you need to manually fill out the IP address, subnet mask, provided by the broadband Operator (network administrator) in the local computer connection, Gateways and DNS. When setting up the Mercury mw3030r router to surf the Internet, you should choose: Static IP.

Select "Static IP" in Internet mode

Set IP address, subnet mask, gateway, DNS information required for static IP Internet access

(4), "Let the router automatically choose the way to access the Internet (recommended)" This option does not recommend that you choose, because the router is sometimes not accurate identification, resulting in the wrong way to choose the Internet.

4. Choose Wireless Working frequency band:

Select: "Wireless work at the same time in the 2.4GHz and 5GHz band"--> "Next".

Wireless Working Band Selection: "Wireless at the same time working in the 2.4GHz and 5GHz band"

5, 2.4G Wireless settings

Set "SSID"--> Select "Wpa-psk/wpa2-psk"--> set "PSK password"--> "Next". As shown in the following figure

Set up the 2.4G wireless network on the Mercury mw3030r router

6, 5G Wireless settings

Set "SSID"--> Select "Wpa-psk/wpa2-psk"--> set "PSK password"--> "Next". As shown in the following figure

Set up the 5G wireless network on the Mercury mw3030r router

Warm tips:

(1), SSID, is the wireless WiFi name, suggested that the combination of letters and numbers, preferably not in Chinese, because some wireless device wireless network card can not recognize Chinese characters, will not be able to search the wireless signal.

(2), PSK password, wireless wifi password, it is recommended to use uppercase and lowercase letters, numbers, symbols of the combination to set, and the length must not be less than 8 bits.

6. Setup Complete

Click "Reboot" to end the Setup wizard.

Mercury mw3030r Router Setup completes reboot