How to continue a breakpoint when WinRAR file is transferred

We often encounter files in the process of transmission, because some accidents sometimes occur breakpoints, such as when using WinRAR compressed files, when using QQ to transfer files, the setting is to use FLASHFXP upload files, then, when the transmission of file breakpoints, how to continue to pass it? Let's take a look at the small series according to different circumstances for everyone to share the solution!

First, using WinRAR to achieve the continuation of the breakpoint

When we copy a folder that contains a large number of files, if a file is damaged or is being used by the system, the copy operation is terminated, although a portion of the file is copied to the destination, and if there are many files, you will not know which files have been copied and which files have not yet been copied. The usual situation is to end or repair the called file and then re-copy, in fact, the use of compression software winrar can be used to bypass the files cannot be copied, the file is sent to the end, but also the files are not copied to find out.

Right click on the folder you want to copy, select "Add to Compressed File", click "Browse" in the "General" page of the compression parameter setting that pops up, navigate to the target path of the copy (e:), confirm the compression, and when it hits the file that can't be copied, winrar will pop up a "diagnostic message" The dialog box prompts for a file that cannot be accessed, and continues to compress until it finishes (below), bypassing the files that cannot be copied to extract most of the files. Unzip the directory to the target path. Click Copy to Clipboard in the dialog box shown in Figure 1, and paste in a text editing tool such as Notepad to see a list of files that were not successfully copied.

Replicating WinRAR diagnostic information

Tip: Use winrar compression packaging to copy files, only a few files more than the size of the case, for a limited number of large files can not be prepared to extract.

　Second, the use of QQ file breakpoint continued transmission

We know that with QQ through the network and remote friends to file, due to network failure or power outage, computer unexpected restart, etc., as long as we re-transfer the file, QQ will be prompted "just received the file size, whether to use a breakpoint continued to receive from the last location?", click Continue to receive The file will continue to be received from the location where it was last interrupted (the image below).

QQ breakpoint continue to transmit function

Using the same method, on the local computer at the same time landing two QQ number, and then use one QQ to send a file to another, even if you close a chat window or restart the computer, and then continue to transfer can also achieve a breakpoint continued transmission.

Tip: Using MSN (Windows Live Messenger) for file transfer can also enable a breakpoint to continue to pass. QQ's breakpoint continuation function is very effective for receiving files from the network, or sending files in the local area network and encountering unexpected conditions that result in transmission termination.

Third, self-built FTP implementation of the breakpoint relay

If you often want to do a lot of file transfer in the local area network, the network speed is poor, the other side shutdown, power outage restart, and so on, if using the above method or appear "amateur" point. FTP server software such as serv-u can be used to build an FTP download server, and then use the FTP software to file a copy of the breakpoint to continue transmission. Here we use the simplest chken FTP software to illustrate.

Run the software into the configuration interface, switch to "group settings" right click Select "New Entry" open the "Add New Group" dialog box, enter the name of the group, set the root of the transfer file, note that the "continue" is checked, switch to "user settings" right-click the new user account, switch to "system settings" option to set up ports and threads, and finally click "Run Service" to start the FTP server (see figure below).

　Chken FTP Add new group settings

After starting the FTP server, we can run FLASHFXP and other FTP software for large file copy transfer, because it is ftp upload and download, so not only fast and can be a breakpoint to continue to pass. For example, we take FLASHFXP as an example to illustrate. After running FLASHFXP, press the F8 key to open the Connection window, the server can choose for the native IP address, enter the user name and password just set to log on to the FTP (as shown below), then can be set up in the virtual directory for large file copy, transfer, or even complete a copy of the whole disk operation, A breakpoint can be resumed even if an unexpected termination occurs.

FLASHFXP Quick Connect Settings

Tip: The local computer to establish an FTP server is a more common practice, similar software is more, this method for the number of files does not affect, even if the transmission of extra large files are not afraid of unexpected termination.