How to mount partition with NTFS file system and read write access

How to mount partition with NTFS file system and read write accesscontents [hide]

• • Introduction
  • Mount
    NTFS file system with read only access
    • NTFS
      Kernel support
    • Identifying
      Partition with NTFS file system
    • Mount
      NTFS partition
  • Mount
    NTFS file system with Read Write Access
    • Install
      Addition Software
      • Fuse
        Install
      • Ntfs-3g
        Install
    • Mount
      NTFS partition with Read Write Access

1. Introduction

Purpose of this article is to provide to reader Step by Step Guide, how to mount partition with NTFS file system on the Linux operating system. This article consists of two parts:

• Mount NTFS file system read only access
• Mount NTFS file system with Read Write Access

2. Mount NTFS file system with read only access2.1. NTFS Kernel support

Majority of current Linux distributions supports NTFS file system out of the box. to be more specific, support for NTFS file system is more feature of Linux kernel modules rather than Linux distributions. first verify if we have NTFS modules installed on our
System.

ls /lib/modules/2.6.18-5-686/kernel/fs/ | grep ntfs 

NTFS module is presented. Let's identify NTFS partition.

2.2. Identifying partition with NTFS file system

One simple way to identify NTFS partition is:

fdisk -l | grep NTFS 

 

There it is:/dev/sdb1

2.3. Mount NTFS partition

First create a mount point:

mkdir /mnt/ntfs 

Then simply use mount command to mount it:

mount -t ntfs /dev/sdb1 /mnt/ntfs 

Now we can access NTFS partition and its files with read write access.

3. Mount NTFS file system with Read Write Access

Mounting NTFS file system with read write access permissions is a bit more complicated. this involves installation of addition software such as fuse and ntfs-3g. in both cases you probably need to use your package management tool such as Yum, Apt-Get, synaptic
Etc .. and install it from your standard distribution repository. Check for packages ntfs-3g and fuse. We take the other path which consists of manual compilation and installation fuse and ntfs-3g from source code.

3.1. Install addition software3.1.1. fuse install

Download source code from: http://fuse.sourceforge.net/

wget http://easynews.dl.sourceforge.net/sourceforge/fuse/fuse-2.7.1.tar.gz 

Compile and install fuse source code:
Extract source file:

tar xzf fuse-2.7.1.tar.gz 

Compile and install

cd fuse-2.7.1./configure --exec-prefix=/; make; make install 

3.1.2. ntfs-3g install

Download source code from: http://www.ntfs-3g.org/index.html#download

wget http://www.ntfs-3g.org/ntfs-3g-1.1120.tgz 

Extract source file:

tar xzf ntfs-3g-1.1120.tgz 

Compile and install ntfs-3g source code
Note: Make sure that you have PKG-config package installed, otherwise you get this error message:

checking for pkg-config... nochecking for FUSE_MODULE... configure: error: FUSE >= 2.6.0 was not found. Either it's not fully installed (e.g. fuse, fuse-utils, libfuse, libfuse2, libfuse-dev, etc packages) or files from an oldversion are still present. See FUSE at http://fuse.sf.net/ 

cd ntfs-3g-1.1120./configure; make; make install 

3.2. Mount NTFS partition with Read Write Access

mount -t ntfs-3g /dev/sdb1 /mnt/ntfs/ 

Note: ntfs-3g recommends to have at least kernel version 2.6.20 and higher.

linuxconfig.org~# mount -t ntfs-3g /dev/sdb1 /mnt/ntfs/WARNING: Deficient Linux kernel detected. Some driver features are         not available (swap file on NTFS, boot from NTFS by LILO), and         unmount is not safe unless it's made sure the ntfs-3g process         naturally terminates after calling 'umount'. If you wish this         message to disappear then you should upgrade to at least kernel         version 2.6.20, or request help from your distribution to fix         the kernel problem. The below web page has more information:         http://ntfs-3g.org/support.html#fuse26