How to Set up a router for China Netcom broadband

Netcom broadband in the router settings will encounter a lot of problems, Here D-LINK Broadband Router as the blueprint for the introduction, the specific steps of router settings.

Preparations before configuration

Broadband routers generally provide a visual setting Interface Based on WEB pages. You can open this interface by entering the management address in the browser. To access this interface, you need to configure the network of the computer used to configure the Broadband Router.

The default Management IP address of the DI-504 Broadband Router is: 192.168.0.1; default subnet mask: 255.255.255.0, these addresses can be changed after you have made the Basic settings. Configure the IP address of the connected computer to the IP address of the same CIDR block as the DI-540 Broadband Router. For example, IP Address: 192.168.0.3, mask: 255.255.255.0, and gateway is the default Management IP address of the router): 192.168.0.1. After completing this configuration, you can officially access the DI-504 Broadband Router and further set up

Basic settings

Start the browser and enter http: // 192.168.0.1 in the address bar. After the connection is established, the logon window is displayed. Enter the administrator username: ADMIN and password: blank. Remember to set it after setting it ), click "OK" to go to the management interface. The basic settings are on the "Homepage", including WAN settings), LAN Settings), and DHCP service settings.

WAN) settings

The Wan setting is the setting of the broadband access line. Because the user chooses different types of broadband access lines, it corresponds to the line of the network service provider in its own access method. There are three WAN types: Dynamic IP address, fixed IP address, and PPPoE dialing. We need to select one of them based on our actual line type.

1. Dynamic IP Address

This function is applicable to Automatically Obtaining IP addresses from ISP Internet service providers. This method has no other settings except the WAN type. Modify the MAC address unless required by the ISP. Click "execute.

2. fixed IP addresses

It is applicable to all the WAN port IP addresses specified by the ISP. If you enter the IP address, subnet mask, gateway, and DNS provided by the ISP, the primary DNS may be entered once ). Do not change the MAC address unless required by the ISP. (MTU maximum transmission unit) Ask the ISP if required. Click "execute.

3. PPPoE

It is applicable to China Telecom, China Netcom, China tietong, and other ADSL dial-up access methods. It is currently the largest number of users in China for broadband access. Select "dynamic PPPoE" or "static PPPoE" for PPPoE. Dynamic PPPoE is generally used to automatically obtain IP addresses from the ISP); static PPPoE is rarely used by the IP address specified by the ISP ).

"PPPoE User Name" is the PPPoE user name provided by the ISP, generally the telephone number of the line); "PPPoE User Password" is the PPPoE user password provided by the ISP, and then enter the password again. The service name is optional. "Ip address" is applicable to the static PPPoE mode, which is specified by the ISP. The primary DNS server and secondary DNS server are provided by the ISP. "Maximum idle time" sets the maximum time for non-active line connection persistence. If the maximum time is exceeded, automatic disconnection is triggered. This function is useful for ADSL with pay-as-you-go billing. We recommend that you select automatic for "online mode. Click "execute ".

LAN) settings

The LAN setting is to set the IP address of the router itself. This is the gateway IP address of the entire intranet, which is used when we assign an IP address to the Intranet host ). The default IP address is 192.168.0.1, And the subnet mask is 255.255.255.0. We need to modify the IP address based on our actual Intranet IP address planning scheme. Click "execute.

DHCP service settings

This is an optional setting, not necessarily required. We can select "Activate" to set up the DHCP server function for the vro to automatically assign IP addresses to the Intranet host. Here, you need to set the starting and ending ranges and lease time of the assigned IP address. Click "execute.

After completing the first and second settings, the network should be able to provide Internet sharing services for the Intranet.