HS5, HS6 high-speed data acquisition card, multi-channel oscilloscope Software Automatic Measurement function Diagram

Hs4, HS5, HS6 virtual oscilloscope

Hs4, HS5, HS6 USB and connected high-speed acquisition card

Multi-channel oscilloscope software has many automatic measurement functions, which can automatically measure the measurement signal of the virtual oscilloscope card or the choice of measurement signal. Use automatic measurements in the oscilloscope to display any details of the tested signal. Two groups of cursors, horizontal and vertical cursors, can be used to indicate and check each part of the signal. Automatic Measurement includes: minimum, maximum, upper and lower limits, Root Mean, mean, variance, standard deviation, and frequency.

The value displayed in the measurement result is displayed in the software pop-up window, which can be located anywhere on the computer screen. A convenient toolbar allows you to click or enable or disable measurement. You can copy the measurement results to the clipboard, for example, using them in a report. The cursor and measurement results are also included when the image is printed.
Multi-channel oscilloscope software allows you to create and arrange graphics as you want. You can create a new graph on the measurement software's home screen and move it to a separate window outside the home screen. When creating a new image, you can completely control the position and size of the image. By arranging charts according to your preferences, you can focus more on the measurement at hand without having to use the required information to locate the chart. This graph can contain range images, spectrum analyzer images, and data recorder images.

Axis
To change the axis offset settings, you only need to capture the axis and drag it to the desired position. See Animation 1.
To change the gain settings, capture one of the ends of the axis and drag it to the preferred position. See Animation 2.
You can also use the mouse wheel to adjust the offset and gain: When the mouse pointer is above the axis and the wheel turns, the offset is adjusted. When the ctrl key is pressed during Wheel rotation, the gain is adjusted.
Measurement
For clarity, not all measurements are enabled by default when the cursor is enabled. In program settings (settings), you can determine which measurements are displayed by default when the cursor is enabled. By default, the cursor window is shown in.
Default cursor
Vertical and/or horizontal cursors are required for left, right, right-left, top, bottom, top-bottom, and slope measurements. They use the cursor position as the result.
All other measurements are calculated within the data range. When vertical cursors are enabled, the data range is marked by vertical cursors. When the Vertical cursor is closed, the data range is equal to the rear sample.
In addition to the calculated values between vertical cursors, the positions of vertical cursors and their differences can be seen at the bottom of the cursor window. The studibasefipe button hides or displays this basic information.
Virtual impedance can be configured for users who can measure dBm by power measurement power and DBM. Click the impedance mpefistion button to allow you to set its value. The default value is 600 ohm.
You can copy the measured value to the clipboard as text by pressing the coptociploboad button.
When you use the alwaysontop button to open alwaysontop, the cursor window cannot be hidden in other windows of the multi-channel oscilloscope software.
To enable or disable a measurement, you can click the corresponding measurement button on the toolbar, and click selectmeasurements to complete ...... In the displayed menu of the cursor window, or click the cursrsstuttread button on the toolbar. The window shown below will pop up, where you can select the desired measurement value.
Cursor measurement selection window
Note: For frequency measurement, there must be at least one cycle between the Vertical cursor. In addition, there must be at least two rising slopes in the signal.
Time Base/frequency reference
The width of the scroll bar indicates the total measurement record, and the width of the slider indicates the visible part of the record. To change the record view offset, capture the slider and drag it to the preferred position (animation 3) or press the buttons on both sides of the scroll bar. To change the record view gain, drag one of the slider's edges left or right to observe the signal changes corresponding to the slider width (animation 4 ).
You can also use the mouse wheel to adjust the offset and gain: When the mouse pointer is above the scroll bar and the wheel turns, the offset is adjusted. When the ctrl key is pressed during Wheel rotation, the gain is adjusted.
Double-click the slider, click the reset zoom button, reset the zoom, or press the hot key t to return the time base to the default zoom state.

More automatic measurement functions of hs4, HS5, HS6 virtual oscilloscope, and high-speed data acquisition card multi-channel Software
Please refer to: www.pc17.com.cn

HS5, HS6 high-speed data acquisition card, multi-channel oscilloscope Software Automatic Measurement function Diagram