Huawei router commands

This article introduces some examples of Huawei 3COM vro commands. in the network, the network administrator should know the status of the vro at any time for timely troubleshooting. The command of the Huawei router is similar to the show command of cisco. Making good use of him can greatly facilitate our daily work.
Aaa specifies AAA (authentication, authorization, and recording) Configuration
Aaa-enable (authentication, authorization, and billing)
Access-server specifies the access server listening port information
Access-tty specifies access client configuration information
Acl specifies access table configuration information
Add an arp table entry for ARP.
Add a banner
Bgp Border Gateway Protocol
Bridge configuration
Clock settings
Configfile select Configuration File
Controller sets the E1/T1/E3/T3 entry
Copy: copy the config or system file to the remote TFTP server.
Enable system debugging for debugging
Delete: deletes the configuration file in FLASH or NVRAM.
Dhcp defines parameters of the DHCP server
Dialer-rule
Display displays system running information
Configure dlsw in DLSw
Download the saved configuration file
Dram-wait sets DRAM wait Status
Configure firewall Status in firewall
First-config sets or clears the initial configuration flag
Flow-interval
Fr Frame Relay global configuration command set
Ftp-server FTP server
Get copies the config or system file from the remote TFTP Server
Set hotkey Information
Test attribute of hwping
Hwping-agent starts the hwping client Function
Hwping-server starts the hwping server Function
Hwtacacs-server configure hwtacacs-server templat
Icmp ICMP configuration command
Idle-timeout: enables EXEC timeout and exits.
Ifquelen: Change the interface queue length
Ike specified IKE parameter configuration information
Info-center specifies Global Information center Configuration
Interface to enter the specified interface command mode
Ip Address Configuration command
Configuration of ipsec-related parameters
Ipx global IPX configuration command subset
Isdn global ISDN configuration command
Set l2tp
L2tp-group specifies L2TP group configuration information
Language mode switch
Leased-modem start or close leased line modem
Local-user specifies to add user configuration information to the System
Logic-channel Configuration Logical channel
Login-method specifies the login usage list
Log out
Multicast specifies multicast configuration information
Nat configuration address translation
Ntp-service NTP Module
Ospf Open Shortest Path Priority Protocol
Pad remote Logon
Pim Protocol Independent Multicast
Ping to check whether the network host connection and host are reachable
Pos-server POS Access server
Ppp Configuration
Printer configure LPD Network printer
Set the protocols supported by the system
Qos service quality command
Radius configuration information
Reboot restarts the vro according to certain conditions.
Reset to clear
Reverse-telnet: Set the reverse telnet Parameter
Rip route information protocol
Route-policy specifies a set of policies.
The router enters the route processing mode.
Rsa specified RSA module configuration information
Save saves the current configuration parameters to FLASH or NVRAM
-String: configure the modem dialing script
Send a message to another terminal
Settr
Snmp-agent specifies SNMP configuration parameters
Configure global sot parameters for SOT
Set ssh attributes in ssh
Standby setting Dynamic Route backup Properties
Subscriber-line voice interface configuration
Sysname
Tcp configuration global TCP Parameters
Telnet Remote Logon
Terminal specifies the configuration information of terminal termplate
Timerange start or stop time zone
Tracert traces the routers at the destination
Translate configuration X2T (X25-To-Tcp) route table
Tty global access settings
Tty-app specifies the terminal access application settings
Undo cancels the command operation or restores to the default value
Update online upgrade of the interface board driver
Userlog
Verify that the version number of the VRP is the same as that of the current VRP.
Voice-setup voice feature settings
Vrrp enabling ping virtual address Switch
X25 X.25 protocol group Layer
X29 specify X29 configuration information

1. Tenda wireless router settings
2. Diagram 2 of ADSL and wireless router networking practices)
3. Illustration 1 of ADSL and wireless router networking)
4. Tutorial on setting a fully-targeted Wireless Router
5. Asus launches "Easy-to-use" cards to compete in the wireless routing Market