Huawei Switch configuration command

The Huawei Switch configuration command [Quidway] dis cur; displays the current configuration [Quidway] display current-configuration; displays the current configuration [Quidway] display interfaces; displays the interface information [Quidway] display vlan all; display route information [Quidway] display version; display version information www.2cto.com [Quidway] super password; modify the privileged user password [Quidway] sysname; Switch name [Quidway] interface ethernet 0/1; go to interface view [Quidway] interface vlan x; go to interface view [Quidway-Vlan-interfacex] ip address 10.65.1.1 255.255.0.0; configure the VLAN ip address [Quidway] Ip route-static 0.0.0.0 0.0.0.0 10.65.1.2; default route = gateway [Quidway] rip; layer-3 switch supports [Quidway] local-user ftp [Quidway] user-interface vty 0 4; go to the virtual terminal [S3026-ui-vty0-4] authentication-mode password; set password mode [S3026-ui-vty0-4] set authentication-mode password simple 555 set password [S3026-ui-vty0-4] user privilege level 3 user level [Quidway] interface ethernet 0/1; enter port mode [Quidway] int e0/1 www.2cto.com; enter port mode [Quidway-Ethernet0/1] duple X {half | full | auto}; Configure port working status [Quidway-Ethernet0/1] speed {10 | 100 | auto}; Configure port working rate [Quidway-Ethernet0/1] flow-control; configure port throttling [Quidway-Ethernet0/1] mdi {traffic SS | auto | normal }; configure port flat connections [Quidway-Ethernet0/1] port link-type {trunk | access | hybrid}; set port working mode [Quidway-Ethernet0/1] port access vlan 3; the current port is added to the VLAN [Quidway-Ethernet0/2] port trunk permit vlan {ID | All}; set the VLAN allowed by the trunk [Quidway-Ethernet0/3] port trunk pvid vla N 3; Set PVID for the trunk port [Quidway-Ethernet0/1] undo shutdown; activate port [Quidway-Ethernet0/1] shutdown; close port [Quidway-Ethernet0/1] quit; return to [Quidway] vlan 3; Create VLAN [Quidway-vlan3] port ethernet 0/1; add port [Quidway-vlan3] port e0/1 in VLAN; [Quidway-vlan3] port ethernet 0/1 to ethernet 0/4; add port [Quidway-vlan3] port e0/1 to e0/4 in VLAN; [Quidway] monitor-port <interface_type interface_num>; specify the Image port [Quidway] port mirror <Interface_type interface_num>; specify the port [Quidway] port mirror int_list observing-port int_type int_num; specify the image and the image [Quidway] description string; specify VLAN description character [Quidway] description Delete VLAN description character [Quidway] display vlan [vlan_id]; view VLAN settings www.2cto.com [Quidway] stp {enable | disable}; Set spanning tree, [Quidway] stp priority 4096 is disabled by default; vswitch priority is set [Quidway] stp root {primary | secondary}; backup set as root or root [Quidway-Ethernet0/1] stp cost 200; settings [Quidway] link-aggregation e0/1 to e0/4 ingress | both; port aggregation [Quidway] undo link-aggregation e0/1 | all; the first port is the channel number [SwitchA-vlanx] isolate-user-vlan enable; the first port is the primary vlan [SwitchA] isolate-user-vlan <x> secondary <list>; set the sub-vlan [Quidway-Ethernet0/2] port hybrid pvid vlan <id> included in the primary vlan; set the pvid of the vlan [Quidway-Ethernet0/2] port hybrid pvid; remove vlan pvid [Quidway-Ethernet0/2] port hybrid vlan vlan_id_list untagged If the vlan id of the package is the same as that of the PVId, the vlan information is removed. The default value is PVID = 1. Therefore, set the PVID to the vlan id and the vlan that can communicate with each other as untagged.