Huawei MA5620 Configure broadband and voice instances

Huawei EPON Configuration Instance  

1 , public sector and broadband PPPOE Part Use the serial user name password root/mduadmin

Ma5620e>enable

Ma5620e#config

ma5620e (config) #

ma5620e (config) #sysname Bigcow/ give the device a name / **** before the Public Ministry

First, build VLANs and addresses

bigcow (config) #vlan built ONU the management vlan/

bigcow (config) #vlan 3001 to 3016/ this ONU is used PPPoE vlan/bigcow (config) #port VLAN 0/0 1/ Allow upstream vlan/

bigcow (config) #port vlan 3001 to 3016 0/0 1/ Allow PPPoE vlan/

Note: ONU you use it. VLAN in the mouth of the Allied , the VLAN used for building switches does not have to be transmitted

Bigcow (config) #int VLAN 100

Bigcow (config-if-vlanif100) #ip add 10.247.32.2 built ONU the management ip/

Bigcow (config-if-vlanif100) #quit One level back  

Bigcow (config) # ip route 0.0.0.0 0.0.0.0 10.247.32.1

second, build users PVC for dialing and transmitting  

Bigcow (config) # undo Service-port All first delete the original PVC before - a ETH Port for PPPoE , - , the , - three ports for cascade building switches  

Bigcow (config) #

Service-port VLAN 3001 ETH 0/1/1 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3002 ETH 0/1/2 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3003 ETH 0/1/3 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3004 ETH 0/1/4 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3005 ETH 0/1/5 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3006 ETH 0/1/6 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3007 ETH 0/1/7 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3008 ETH 0/1/8 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3009 ETH 0/1/9 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3010 ETH 0/1/10 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3011 ETH 0/1/11 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3012 ETH 0/1/12 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port VLAN 3013 eth 0/1/13 user-vlan untagged rx-cttr 6 tx-cttr 6

Pass through the mouth  

(config) #service-port vlan transparent ETH 0/1/14 other-all rx-cttr 6 tx-cttr 6

(config) #service-port vlan transparent ETH 0/1/15 other-all rx-cttr 6 tx-cttr 6

(config) #service-port vlan transparent ETH 0/1/16 other-all rx-cttr 6 tx-cttr 6

Last Save Exit  

Bigcow (config) #save

Bigcow (config) #quit

2 , phone part configuration  

(config) #voip

(CONFIG-VOIP) #ip address media 10.247.32.2 10.247.32.1 / The front address for this device is managed by

Address is the gateway address, which means that the two addresses will change according to the actual address / 

(CONFIG-VOIP) # IP address signaling 10.247.32.2 / This device management address, address will change /(config) #interface h248 0

(config-if-h248-0) # if-h248 attribute Mgip 10.247.32.2 mgport 2944 transfer UDP

/ This device manages the address and the address will change. / 

(config-if-h248-0) #if-h248 attribute mgcip_1 58.242.3.158 mgcport_1 2944/ fixed Address /

(config-if-h248-0) #if-h248 attribute mgcip_2 58.242.3.186 mgcport_2 2944/ fixed Address /

(config-if-h248-0) #if-h248 attribute mg-media-ip 10.247.32.2 / This device management address, address will change /

(config-if-h248-0) #if-h248 attribute start-negotiate-version 2

(config-if-h248-0) #mg-software parameter 2 2/ initiate dual attribution, corresponding to the core /  

(config-if-h248-0) #reset Coldstart

(config) #esl user/ Associating user lines / 

(config-esluser) #mgpstnuser batadd 0/2/1 0/2/16 0 terminalid 0 (config)

#save

Huawei MA5620 Configure broadband and voice instances