I386™The system starts to install FreeBSD Step 2-view the device detection results

The last few hundred lines displayed on the front screen will be in the buffer for you to check.

To browse the buffer, you can pressScroll lockThis will enable the screen scrolling function. Then you can use the direction key orPageup,PagedownKey. RepressScroll lockThe key stops the screen scrolling.

You will see a similar picture when browsing. The real result varies depending on your computer device.

Figure. Typical device detection results

avail memory = 253050880 (247120K bytes)Preloaded elf kernel "kernel" at 0xc0817000.Preloaded mfs_root "/mfsroot" at 0xc0817084.md0: Preloaded image </mfsroot> 4423680 bytes at 0xc03ddcd4md1: Malloc diskUsing $PIR table, 4 entries at 0xc00fde60npx0: <math processor> on motherboardnpx0: INT 16 interfacepcib0: <Host to PCI bridge> on motherboardpci0: <PCI bus> on pcib0pcib1:<VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0pci1: <PCI bus> on pcib1pci1: <Matrox MGA G200 AGP graphics accelerator> at 0.0 irq 11isab0: <VIA 82C586 PCI-ISA bridge> at device 7.0 on pci0isa0: <iSA bus> on isab0atapci0: <VIA 82C586 ATA33 controller> port 0xe000-0xe00f at device 7.1 on pci0ata0: at 0x1f0 irq 14 on atapci0ata1: at 0x170 irq 15 on atapci0uhci0 <VIA 83C572 USB controller> port 0xe400-0xe41f irq 10 at device 7.2 on pci0usb0: <VIA 83572 USB controller> on uhci0usb0: USB revision 1.0uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr1uhub0: 2 ports with 2 removable, self poweredpci0: <unknown card> (vendor=0x1106, dev=0x3040) at 7.3dc0: <ADMtek AN985 10/100BaseTX> port 0xe800-0xe8ff mem 0xdb000000-0xeb0003ff irq 11 at device 8.0 on pci0dc0: Ethernet address: 00:04:5a:74:6b:b5miibus0: <MII bus> on dc0ukphy0: <Generic IEEE 802.3u media interface> on miibus0ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, autoed0: <NE2000 PCI Ethernet (RealTek 8029)> port 0xec00-0xec1f irq 9 at device 10.0 on pci0ed0 address 52:54:05:de:73:1b, type NE2000 (16 bit)isa0: too many dependant configs (8)isa0: unexpected small tag 14orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq2 on isa0fdc0: FIFO enabled, 8 bytes thresholdfd0: <1440-KB 3.5'' drive> on fdc0 drive 0atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0atkbd0: <AT Keyboard> flags 0x1 irq1 on atkbdc0kbd0 at atkbd0psm0: <PS/2 Mouse> irq 12 on atkbdc0psm0: model Generic PS/@ mouse, device ID 0vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0sc0: <System console> at flags 0x100 on isa0sc0: VGA <16 virtual consoles, flags=0x300>sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0sio0: type 16550Asio1 at port 0x2f8-0x2ff irq 3 on isa0sio1: type 16550Appc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0pppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE modeppc0: FIFO with 16/16/15 bytes thresholdplip0: <PLIP network interface> on ppbus0ad0: 8063MB <IBM-DHEA-38451> [16383/16/63] at ata0-master UDMA33acd0: CD-RW <LITE-ON LTR-1210B> at ata1-slave PIO4Mounting root from ufs:/dev/md0c/stand/sysinstall running as init on vty0

Check the test results carefully to make sure That FreeBSD finds all the devices you want to appear. If no device is found, it is not listed. The custom kernel allows you to add defaultGenericDevices not supported by the kernel, such as sound cards.

In FreeBSD 6.2 and later versions, Figure 2-3 is displayed after the system device is detected. Use the cursor key to select a country or region. Then pressEnterThe system automatically sets the region and keyboard ing. You can also log out easily.SysinstallAnd start from scratch.

Select country and region menu

 

Select exit sysinstall

 

On the main interface, select exit install as the direction key and you will see the following information:

                      User Confirmation Requested          Are you sure you wish to exit? The system will reboot            (be sure to remove any floppies/CDs/DVDs from the drives).                            [ Yes ]    No

If CDROM is still in the optical drive and [Yes] is selected, the installer restarts.