In-depth introduction and Setup of tp-link router interfaces

In-depth introduction and setup of the tp-link router interface, colleagues are responsible for the introduction of the tp-link router interface, which is a very large project. Outsiders may be confused. The following are just some of the details of this problem, but for beginners who do not know anything about it, it is enough for you to have a new understanding of the tp-link router interface.

The first condition for the introduction of the tp-link router interface is that a vro can have four, eight, 16, or more ports. If you have many computers, you can buy a vswitch with multiple ports. there are several direct connections to the network cable, one in the telecom mode or you do not need to use the mode if you are a leased line ).

 

Introduction to tp-link router interfaces

A vro can be used if there are at least two or more pc computers. However, the meaning of using a vro is lost. in fact, tp-link company out of the router, such as TP-LINKTL-402M or 40 m or other models of tp-link router, most of the methods to open the routing is similar. this article takes TP-LINKTL-402M as an example, please see the picture.

 

Introduction to tp-link router interfaces

The tp-link router is introduced here. You only need to follow the picture to correctly connect the PCs, Telecom broadband modes, and routers to each other, so a network has been set up. the following describes how to enable the routing function. if all cables have been connected. we can open a connected PC at any time.

 

Introduction to tp-link router interfaces

Enable the network neighbor attribute (Image 2), local connection attribute (image 3), TCP/IP protocol attribute (Image 4), and set the ip address to 192.168.1.2 subnet: 255.255.255.0 Gateway: 192.168.1.1 (image 5) are you sure you want to configure the DNS After configuring the vro. note: For 98 and me systems, go to control panel network connection to set up. here, xp is used as an example. See the picture.

 

Introduction to tp-link router interfaces

By the way, I would like to remind you that IP address ranges can be set between 192.168.1.2 and 192.168.1.254. Do not set the same IP address to multiple computers. This will cause IP address conflicts. remember. okay. I can open InternetExplorer on the desktop, enter 192.168.1.1 and press Enter. See the picture.

 

Introduction to tp-link router interfaces

Enter the user name and password. The default user name and password are admin, which is also written in the vro manual. enter and press enter to enter the vro configuration page. note: The default IP address of the tplink router is basically 192.168.1.1 and the password is basically the first time that the admin enters the router interface. See the picture.

 

Introduction to tp-link router interfaces

Here we select the setting wizard. Please see the picture, and then next, please see the picture. We select adsl virtual dialing here. Most of us choose it. The other static data is selected by the leased line. We will not detail it here. We know broadband users, tietong, China Netcom and other virtual dialing users, select it, and then see the image next.

 

Introduction to tp-link router interfaces

Click Next to see image 11. Click Finish to set the route. now, all the configurations in the vro are set. Now we can only restart the vro. click the system tool and restart the router. It will take a few seconds. Please refer to the picture.

 

Introduction to tp-link router interfaces

At this time, we close the configured webpage window and connect to other computers to access the Internet. note: Because the DHCP service of the vro is automatically enabled, you only need to connect to the PC, and the vro will assign an IP address to the computer. Therefore, no other computer needs to be set, connect the vro or vswitch directly with a network cable to access the Internet.

Of course, you can also manually set the IP Address: IP Address Setting range: 192.168.1.2-192.168.1.254 subnet: 255.255.255.0 Gateway: 192.168.1.1DNS: You can set the DNS provided by the local telecom, if you do not know the local DNS address, you can set the preferred DNS to 192.168.1.1, that is, the gateway. now, we need to set the DNS address of this PC, so we will not talk much about the method. Open the local connection attribute of the network neighbor attribute, TCP/IP protocol attribute. Please refer to the picture.

 

Introduction to tp-link router interfaces

It is the local telecom DNS address. figure 15: The DNS address is the gateway address. Note: The above figure 14 sets the local telecom DNS address. You need to set it according to your local telecom DNS address.