Initial test bv561evb Development Board

Source: Internet
Author: User

Today, we got a Development Board, bv561evb, from Hefei Youshi technology. It consists of a basic board and a power board. It is very small and exquisite, and it looks like 10 cm x 7cm. Connect the 12 V power cord, connect to the serial port, open the Super Terminal, configure it to 115200-n-1, then connect the network cable, everything is ready! Turn on the power, the system has been written on the board boot, from the Super Terminal can see the following information: U-Boot-1.1.3-ADI-2006R1 (May 21 2007-11:22:42) Adi BF533/561 U-boot support by besovideo Co. ltdserial port initialized with baud rate = 115200cpu: adsp bf561 rev 0.3 Board: besovideo bf561 Board (http://www.besovideo.com) Clock: VCO: 330 MHz, core: 330 MHz, system: 66 mhzsdram memory map: 0x00000000-0x03ffffff (64 MIB) trcd: 3, TRP: 3, tras: 6, twr: 2, CAS latency: 3 (sclk cycles) Flash: 0x20000000-0x207fffff (16 MIB) device ID: 0x18 (type 'flinfo 'For information on sectors) in: serialout: serialerr: seriali2c: readyautobooting in 2 seconds, press "" To stop ## booting image at 20040000... image name: bfin uClinux kernel created: 11:14:41 UTC image type: Blackfin Linux kernel image (gzip compressed) data size: 1770801 bytes = 1.7 MB load addres S: 00001000 entry point: 00001000 verifying checksum... OK Uncompressing kernel image... linux version 2.6.18-ADI-2007R1-hhbf (huangning @ bvwork00) (GCC zookeeper 3.4.6 (ADI CVs) #252 Tue May 15 16:32:24 CST 2007 Blackfin support (c) 2004-2006 ANUE devices, inc. compiled for ADSP-BF561 rev. 0.3 warning: Unsupported chip revision ADSP-BF561 rev. 0.3 detectedblackfin uClinux support by http://www.hhcn.org /Processor speed: 495 MHz cclk and 99 MHz sclkboard memory: 64 mbkernel managed memory: 32 mbmemory map: TEXT = 0x00001000-0x00135b44 init = export data = 0x00140b40-0x00179624 stack = 0x00142000-0x00144000 BSS = export available = export rootfs = export DMA zone = export cache enableddata cache enabled (write-thro Ugh) Hardware trace enabledbuilt 1 zonelists. total pages: 6912 kernel command line: Root =/dev/mtdblock4 RW mem = 32 m max_mem = 64 m console = ttys0, 115200n8 lpj = 1974272 HDB = noprobe ide0 = noprobedomaining Blackfin priority driven interruptspid hash table entries: 128 (Order: 7,512 bytes) dentry cache hash table entries: 4096 (Order: 2, 16384 bytes) inode-Cache hash table entries: 2048 (order: 1, 8192 bytes Physical pages: 1b00memory available: 4096 K romfs + 25760 K/31485 k ram (41 K init code, 1234 K kernel code, 79 K data, 1024 k dma) blackfin scratchpad data SRAM: 4 kbblackfin data_a SRAM: 16 kbblackfin data_ B SRAM: 16 kbblackfin instruction SRAM: 16 kbcalibrating delay loop (skipped )... 987.13 bogomips presetmount-Cache hash table entries: 512net: Registered protocol family 16 Blackfin gpio controllerbl Ackfin DMA controllerhhbf_init (): Registering device resourcesnet: Registered protocol family 2ip route cache hash table entries: 256 (Order:-2, 1024 bytes) TCP established hash table entries: 1024 (Order: 0, 4096 bytes) TCP bind hash table entries: 512 (Order:-1, 2048 bytes) TCP: Hash Tables configured (established 1024 bind 512) TCP Reno registeredio scheduler Noop registered (default) pfx: pfbits Driver for bf53xserial: 8250/16550 driver $ revision: 1.6 $2 ports, IRQ sharing enabledserial8250: ttys10 at I/O 0x24000000 (IRQ = 76) is a port_st16c2552serial8250: ttys11 at I/O 0x26000000 (IRQ = 77) is an port_st16c2552serial: Blackfin serial driverbfin-uart.1: ttys0 at mmio 0xffc00400 (IRQ = 35) is a BFIN-UARTPPP Generic Driver version 2.4.2ppp deflate compression module registeredppp BSD compr Ession module registeredslip: Version 0.8.4-NET3.019-NEWTTY (Dynamic Channels, max = 256) (6 bit encapsulation enabled ). cslip: Code copyright 1989 Regents of the University of California. slip linefill/keepalive option. ezkit561 map: Mapping 8 MIB flash at 0x200020.bf561 ezkit map: found 1x16 devices at 0x0 in 16-bit banknor chip too large to fit in mapping. attempting to upload... intel/sharp extende D query table at 0x0031using buffer write ratio: erase suspend on write enabledreducing visibility of 16384kib chip to 8192 kibcreating 4 MTD partitions on "bf561 ezkit map": 0x0000-0x00040000: "Das U-Boot" 0x00040000-0x00200000: "factory Linux kernel" kernel: "User Linux kernel" 0x00400000-0x00440000: "coreb image" uClinux [MTD]: Ram probe address = 0x1b00000 size = 0x 400000 creating 1 MTD partitions on "Ram": Role: "ext2fs" uClinux [MTD]: Set ext2fs to be root filesystemtcp Bic registerednet: Registered protocol family 1net: Registered protocol family 17net: registered protocol family 15vfs: mounted root (ext2 filesystem ). freeing unused kernel memory: 40 k freed (0x136000-0x13f000) dma_alloc_init: dma_page @ 0x01a55000-256 pages at 0x01f00000 I Nit started: busybox v1.4.0.svn (17:53:21 Cst) Multi-call binarycat:/etc/issue: no such file or directorycat:/etc/version: no such file or directoryhhbf-i2c: SCL-PF0, SDA-PF1; 166 kHz; temperature: video decoder chip attached, rev 0x11 at 0x4amodprobe: module should not foundmodprobe: failed to load module bfin_pflags <dm9ks> I/O: 2c000300, vid: 90000a46 BF-COREB proc-Fs: v0.2. 0isl12027: detected and attatchedrtc Driver Based on I2C v0.10 (10:08:35, May 13 2007) Welcome: ____ _/__| | _ ____ _/| | // | _ | |__ | _ |/| ___/____ | _ | /____ |/_/| _ | For further information see: http://www.uclinux.org/http://blackfin.uclinux.org/http://www.besovideo.com/ BV561-CDMA>-# can see that the system is guided by U-boot, directly into uClinux, Very simple. Press the Space key to interrupt the system before u-boot does not boot. Press help and you will see a bunch of commands :? -Alias for 'help' askenv-Get environment variables from stdinautoscr-run script from memorybase-print or set address offsetbdinfo-print board info structureboot-boot default, I. E ., run 'bootcmd' bootd-boot default, I. E ., run 'bootcmd' bootelf-boot from an elf image in memorybootm-boot application image from memorybootp-boot image via network using Bootp/TFTP protocolbootvx-boot v Xworks from an elf imagecmp-memory compareconinfo-print console devices and informationcp-memory copycrc32-checksum calculationdate-Get/set/Reset Date & timedcache-enable or disable data cacheecho-echo ARGs to consoleeeprom -EEPROM sub-systemerase-erase flash memoryfl-flush a file to flash memoryflinfo-Print flash memory informationfsinfo-print information about filesystemsf Sload-load binary file from a filesystem imagego-Start application at address 'add' help-print online helpicache-enable or disable instruction cacheicrc32-checksum calculationiloop-infinite loop on address rangeimd-I2C Memory displayiminfo-print header information for application imageimls-list all images found in flashimm-I2C Memory modify (auto-incrementing) imw-memory write (Fill) INM-memory modify (constant address) iprobe-probe to discover valid I2C chip addressesisdram-print SDRAM configuration informationitest-return true/false on Integer compareloadb-load binary file over serial line (Kermit Mode) loads-load S-record file over serial lineloop-infinite loop on address rangels-list files in a directory (default/) MD-memory displaymm-memory modify (Auto-incrementing) mtest-simple Ram testmw-memory write (fill) nfs-boot image via network using NFS protocolnm-memory modify (constant address) OC-over clockingping-Send ICMP echo_request to network hostprintenv-print Environment failed-enable or disable flash write protectionrarpboot-boot image via network using RARP/TFTP protocolreset-perform reset of the cpurun-run Commands in an environment sequence-save environment variables to persistent sequence-set environment variablessleep-delay execution for some timetftpboot-boot image via network using TFTP protocolversion-print monitor version try again in vdsp5 -boot. Connect to the simulator, open the original compiled u-boot-2008r1, modify the clock configuration, run: U-boot 1.1.6 (ADI-2008R1) (Jun 27 2008-00:04:51) CPU: adsp bf561-0.3 (detected Rev: 0.3) board: ADI bf561 ez-kit lite board support: http://blackfin.uclinux.org/clock: VCO: 330 MHz, core: 330 MHz, system: 66 mhzram: 64 mbflash: 16 MB *** warning-bad CRC, using default environment in: serialout: serialerr: serialhit any key to stop autoboot: 0 bfin> Haha, a new board is used to celebrate. Thank you for your support!

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.