Install and configure the built-in ADSL Modem

In some devices, we use the hardware with built-in ADSL Modem. So how to set it? What is the difference from the external ADSL Modem we normally use? Next we will explain it. The built-in ADSL Modem card corresponds to the common built-in "cat". With it, you can enjoy the fast and easy access to ADSL without installing the NIC. however, before using the built-in ADSL Modem card to access the Internet, you need to set this built-in card different from the external ADSL Modem, next, I will introduce the specific setting methods for users!

1. First, install the ADSL card in the computer slot. During installation, you must first turn off the computer power, open the computer shell, find the idle PCI slot, and remove the dust Plate of the corresponding slot, insert the ADSL card strength into the PCIe slot, and tighten the screws to fix the ADSL card;

2. Insert the port on one side of the telephone Line into the ADSL card, and the other end is connected to the voice separator. Here I want to remind you that the telephone Line is directly connected to the Line interface on the separator, the ADSL interface on the separator is connected to the built-in ADSL Modem card, while the Phone interface is connected to the telephone line;

3. After the ADSL card is installed, turn on the computer power to start the system. After Entering the Windows interface, the system can automatically detect the newly installed unknown device, click "Next" as prompted to search for the latest ADSL card driver. After copying the relevant driver, the system will automatically detect the ADSL card;

4. When the "Service Option" Service window appears, you can select the "Advanced" button. In the Advanced Settings dialog box that appears, you must enter the correct VPI and VCI values (which are generally provided by the vendor), and set Framing to the "LLC/SNAP" option;

5. In the ADSL mode setting item in the setting box, you must select the mode recommended by the vendor, and then click "OK, then you can return to the service selection page and click "Next". If the system prompts you to insert a Windows disc, you can directly Insert the disc, then, click "OK". When the new hardware wizard setting box appears, click "finish" to restart the computer;

6. After the built-in ADSL card is installed, you can configure the "network" parameter of the computer. double-click "my computer" and open the "control panel" window. Double-click the "network" icon to open the "Network Properties" window. In the "configuration" column, move the scroll bar to find and select the "TCP/IP/adsl pci nic" option, and then click "properties;

7. After opening the attribute settings window of the ADSL card, you can fill in the DNS settings only, instead of setting IP addresses, subnet masks, and gateway parameters, because these parameters are not used during dial-up. in the "DNS configuration" Settings, you can select "Enable DNS" and enter the name of the computer you used in the host column;

8. In the "DNS server search order" setting, you must enter the Domain Name Server address or other valid Domain Name Server address provided by the local ISP correctly, for example, the ISP address here is 202.102.11.141. Click "add", "OK", and the system restarts the computer;

9. You need to set the VCI and VCI parameters of the built-in ADSL card. You can open the control panel and network window in sequence, select the ADSL built-in card "adsl pci nic" in the network window, select "properties" with the mouse, and click "advanced" in the displayed Properties window, in this setting column, you can set "VCI" to "35" and "VCI" to "32 ", at the same time, set "VPI" under the settings interface to "0", finally select "OK", and then restart the computer;

10. If you use ADSL to access the Internet in Windows 9x, you also need to install the virtual dialing software. currently, there are two types of virtual dialing software: EnterNet300 and WinPoET. When installing the EnterNet300 virtual dialing software, you can use the default quick installation method to install the program, the installation process is exactly the same as that of a common program;

11. After the virtual dialing software is installed, you will see the EnterNet300 shortcut on the desktop. At the same time, on the properties page of the network component, you will also see a piece named "Efficient Networks Enternet P. p. p. o. E Adapter "virtual network card;

12. Double-click the EnterNet300 shortcut icon to open the virtual dial-up interface. Click Create new profile on the right of the interface to Create a new ADSL dial-up connection, enter a proper name for the connection. when you are prompted to enter the user name and password, you can enter the password you applied for in advance;

13. Follow the on-screen prompts to establish the Enternet300 dial-up connection. After that, you will see the dial-up connection established in front of the Enternet300 main interface on the right. double-click the dial-up connection and click "Connect" to Connect to ADSL. Click the Enternet300 connection icon in the lower-right corner of the system taskbar to view the detailed connection status.

Now, you have completed all the tasks for configuring the built-in ADSL Modem card. The following task is to easily surf the internet!