Instance resolution TP-link router for multi-person Internet access

TP-Link RouterHow can I set up to allow several people to access the Internet together? Let's take a look at the following setting process!

1. First, connect your computer and the TP-Link router to the network. Connection Method: connect the line from the ADSL cat to the WAN port of your TP-Link router. The remaining lanports can be connected to your computer or vswitch.

2. Set your IP address to 192.168.1.254 and the subnet mask 255.255.255.0. All the way to OK, ipconfig (entered at the command prompt) confirms that your IP address has changed to 192.168.1.254.

3. Open IE, enter 192.168.1.1 in the address bar, and press Enter. On the screen, enter the user name and password, and enter the default user name and password of the TP-Link router. The general user name and password are admin. For other TP-Link routers, refer to the instructions)

4. After Entering the page, the setting Wizard will pop up. It does not matter if it is not displayed. Click "setting wizard" in the navigation bar on the left. The welcome information of the wizard appears on the right. Click "Next"

5. Select "ADSL virtual dialing PPPoE)" and click Next.

6. Enter the user name and password, which are the user name and password you used when dialing through ADSL.

7. Click "finish". If you are using a monthly subscription, we suggest you do the following work. If you are timing, we recommend that you directly jump to the DHCP Settings section.

8. Click "Network Parameters"> "WAN Port Settings" in the left navigation bar"

9. Select "Automatic Connection" and click "save". In this case, the broadband connection is set. You can click "running status" in the left navigation bar ", click Next to view the WAN port status in the right window. If the "disconnected" button is displayed, the connection is normal.

DHCP server settings for TP-Link vro settings

This function allows computers in the network to access the Internet through the TP-Link router without any network settings.

1. Click "DHCP server" in the left navigation bar and follow the settings below.

DHCP server: Enabled

Address pool start address: 192.168.1.2

Address pool end address: 192.168.1.200

Address rental period: 120 minutes

Gateway: 192.168.1.1

Default Domain Name: not required

Primary DNS server: 202.100.4.15

Backup DNS server: 61.134.1.4

2. Click "save"

Okay! Now, change the TCP/IP Settings of all computers to automatically obtain the IP address, and then restart the computer to access the Internet! I used ADSL to access the Internet and set up a LAN. On the second floor, I had five computers downstairs and four computers upstairs. I have two TP-Link routers. The first floor is the entrance of ADSL. After I connect ADSL to the WAN port of the route and set parameters related to the TP-Link router on the first floor, the computer on the first floor can access the Internet normally. a lan port on the TP-Link router on the first floor is connected to the WAN port of the TP-Link router on the second floor, but the computer on the second floor cannot access the Internet, connect the network cable connected from the TP-Link router on the first floor to the LAN port of the TP-Link router on the second floor. PING the gateway 192.168.1.1 and ask Damo and experienced friends to help me solve the problem.

Set the TP-Link router on the second floor as follows: Change the WAN port to a static IP address, that is, assign it a static IP address on the first floor, change the IP address range of the LAN port on the second floor to a different one on the first floor. Example:

Route settings on the first floor:

WAN: PPPOE dial

LAN: 192.168.1.1

DHCP: 192.168.100 to 192.168.1.150

Second-floor route settings:

WAN: 192.168.1.10

GATWARE: 192.168.1.1

DNS master: 192.168.1.1

LAN: 192.168.2.1

DHCP: 192.168.2.100 to 192.168.2.150

Add: Enable the static IP address of the TP-Link router on the first floor:

Destination IP Address: 192.168.2.1

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

Appendix: how to restore factory settings

The TP-Link router usually has a "reset" reset button to turn off the power supply. Press this button and turn on the power supply for about 3 seconds. Just release the button, generally, the configuration can be restored to the factory default. See the instructions. Different TP-Link routers may have different practices.