iOS XE6 Mobile Development Environment (7): Install XE6 paserver in Mac OSX 10.8 (there is a picture of the truth)

iOS XE6 Mobile Development Environment (7): Install XE6 paserver in Mac OSX 10.8 (there is a picture of the truth) 2014-08-22 21:06

There are few articles on the mobile development environment that can be found on the Delphi XE series online, so this article will try to tell you the answers you want with detailed content and silly expressions.

Before installing Paserver, we first configure the Mac IP, given a fixed intranet IP, so that our XE6 can better connect it!
---------------------------------------------------------------

1. Open the virtual machine, in the Mac, click on the Desktop (the Star map Anywhere), in the Finder select ' Go ', ' application '.

2. In the application window, double-click ' System Preferences '.

3. Double-click ' Network '.

4. In the configuration IPv4, select ' Use DHCP (manually set address) ' or ' manual assignment ' can be, IP address we fill in a fixed intranet IP, only need to be with our windows in the same network segment can, click ' Application '.
It is explained here that our situation is that the real machine is one of the computers under the router, so after the virtual machine has loaded the Mac, we will set the Mac to the same network segment as the real machine so that XE6 can quickly find the paserver.
Mac network Settings and Windows is the same operation, if not, please Baidu a bit.
After Setup is complete, if you need the Mac to be able to access the network, you have to make sure that the IP, subnet mask, gateway, and DNS are set correctly.

Install Paserver.
---------------------------------------------------------------

5. Insert the USB drive, and under Windows, copy the Paserver folder in the XE6 installation directory to the USB flash drive.

6. Copied to USB flash drive. At this point, close all open USB drive windows, and do not read and write to the USB drive.

7. In the virtual machine, connect the USB drive. Let's click the small icon for the mobile device of the status bar in the lower right corner of the virtual machine.

8. Click ' Connect (connect to host) '.

9. The small icon becomes bright, the green status light appears, indicates that the loading USB stick succeeds.
Here is a note: Before this step, you should close the windows of all the open USB drives, but do not need to exit the USB flash drive.
Under VM9, at the same time, a physical device can only be monopolized by one system, whether it is a physical or virtual machine.
We can understand the rules of the virtual machine loading USB drive: When the virtual machine loads the USB drive, it will automatically disconnect the USB flash drive from Windows, and then the virtual machine takes over; Conversely, when the USB drive is disconnected from the virtual machine, Windows takes over the USB drive.
Therefore, if the virtual machine cannot disconnect the Windows USB flash drive, it cannot be loaded, so you must first close the open USB Flash drive window and stop access to the USB drive under Windows.

10. Click on the desktop (the Star map Anywhere), select ' Go ', ' personal ' in the finder.

11. In the Open Personal folder, click on the bottom left corner of our USB stick name, enter the U disk, double hit open Paserver folder.

12. After entering Paserver, double-click radpaserverxe6.pkg to install.

13. Ready to install, click ' Continue '.

14. Agreement, no tube, because an estimated 99% people will not look slowly, we click ' Continue '.

15. Agreement, consent is required, we click ' Agree '.

16. Do not change the installation location, we directly click ' Install '.

17.MAC site Apple, you have to put something on its site, you have to verify your identity, we here fill in the login Mac username and password, click ' Install Software '.

18. After installation, click ' Close '.

19. After the installation is complete, the interface disappears, back to the USB flash drive interface, we check whether the installation is really successful, point ' application '.

20. In the application window, we pulled down the scroll bar to find the RAD paserver XE6, and sure enough the installation was successful, Apple didn't cheat us oh.

So far, XE6 's paserver has been successfully installed in Mac OSX 10.8.

Next, we'll configure XE6 's iOS SDK to make it easy to connect to your Mac to develop our app.

Ps:
---------------------------------------------------------------
Firemonkey Mobile development can add QQ Group: 165232328 (I am not the administrator, just one of the members, this group of experts in groups, looking forward to all of you Delphi enthusiasts to exchange).

iOS XE6 Mobile development Environment (7): Install XE6 paserver in Mac OSX 10.8 (there's a picture of the truth)