Layer-3 Switch implements VLAN communication and rip Routing

Lab name: Use a layer-3 Switch to implement communication and rip routing between different VLANs

Tutorial topology:

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M02/45/E0/wKioL1Psz8jTvsBfAAC_AZ6gzgI409.jpg "Title =" image007.png "alt =" wkiol1psz8jtvsbfaac_az6gzgi409.jpg "/>

Tutorial steps:

(1) first configure the VLAN for the switch, and then assign the IP address and gateway to each host.

(2) Configure VLAN for a layer-3 Switch

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M00/45/DF/wKiom1PszrzDYM7NAACcPzXBtwA541.jpg "Title =" image008.png "alt =" wkiom1pszrzdym7naaccpzxbtwa541.jpg "/>

(3) configure the trunk link for the layer-3 Switch

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M01/45/DF/wKiom1PszsfwRktUAAFX97r7roE243.jpg "Title =" image009.png "alt =" wkiom1pszsfwrktuaafx97r7roe243.jpg "/>

(4) set IP addresses for VLANs and enable the routing function

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M01/45/E0/wKioL1Ps0ArxR96hAAIYXPstR8w873.jpg "Title =" image010.png "alt =" wkiol1ps0arxr96haaiyxpstr8w873.jpg "/>

(5) Verify communication between two VLANs

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M02/45/DF/wKiom1Pszv2RAFmtAAEyXVuXsy0686.jpg "Title =" image011.png "alt =" wkiom1pszv2rafmtaaeyxvuxsy0686.jpg "/>

(6) configure an IP address for the interface of the layer-3 switch connected to the router-then configure the router

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M01/45/E0/wKioL1Ps0CSz2RYQAAGLa5bKkRo756.jpg "Title =" image012.png "alt =" wkiol1ps0csz2ryqaagla5bkkro756.jpg "/>

(7) configure the rip dynamic routing protocol for layer-3 switches and routers

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M02/45/E0/wKioL1Ps0EmwIk5_AAFg6g-bcno600.jpg "style =" float: none; "Title =" image013.png "alt =" wKioL1Ps0EmwIk5_AAFg6g-bcno600.jpg "/>

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M01/45/DF/wKiom1PszzCgk9VjAAFNujhe3Ig659.jpg "style =" float: none; "Title =" image014.png "alt =" wkiom1pszzcgk9vjaafnujhe3ig659.jpg "/>

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M01/45/DF/wKiom1PszzCSvuDSAAH8gXmUvkw007.jpg "style =" float: none; "Title =" image015.png "alt =" wkiom1pszzcsvudsaah8gxmuvkw007.jpg "/>

(8) Verify communication

650) This. width = 650; "src =" http://s3.51cto.com/wyfs02/M02/45/E0/wKioL1Ps0FbxtoM2AAFVkGYZ44Q294.jpg "Title =" image016.png "alt =" wkiol1ps0fbxtom2aafvkgyz44q294.jpg "/>

Summary: In this experiment, the focus is on the configuration of layer-3 switches (1) Encapsulation before creating a trunk link When configuring a layer-3 Switch (2) by default, a layer-3 switch does not enable routing. All routing functions must be enabled after the IP address is configured for the VLAN (3) no switchport is required when configuring an IP address for the interface connecting a layer-3 switch to a vro. Because the vswitch port cannot be configured with an IP address, you need to convert it to the interface of the vro (4) the rip route is the rip dynamic route that adds the directly connected network.