LILO configuration in red-flag Linux

In Linux, LILO is an important file used to realize coexistence of multiple operating systems. LILO is short for LinuxLoader and used for multiple choices during system loading and startup.

In Linux, LILO is an important file used to realize coexistence of multiple operating systems. LILO is short for Linux Loader and used for multiple choices during system loading and startup, if you have installed multiple operating systems, you can use LILO to select which operating system to enter during startup.

Red-Flag Linux desktop 2.4 provides the graphical startup configuration tool "Klilo", which can manage most of LILO's attributes and has friendly interfaces and convenient operations. However, if you are familiar with LILO configurations, you can use manual configuration to configure your machine more accurately.

You can modify LILO by modifying the File "/etc/lilo. conf". after the modification, run the "lilo" command. In LILO, a typical boot mode consists of two parts: one is started with "image =", which is used to guide Linux. The other one starts with "other =" and is used to guide DOS or Windows.

In LILO, the default boot system is ranked first. to modify the default boot system, you only need to switch the positions of the two parts.

LILO usually displays some prompts on the screen when guiding the system. LILO keeps the information on the screen for a while so that you can see it clearly.

Similarly, after modifying the File "/etc/lilo. conf", run the LILO command again to make it take effect.

In some cases, if the physical memory is greater than 64 MB, LILO may not detect all the memory, but uses the first 64 MB memory in the default configuration. Run the following command to know how much memory is used in Linux:

$ Cat/proc/meminfo

If the above problem occurs, you can solve this problem by modifying the/etc/lilo. conf file. The specific method is to add a similar statement before the first "image =" statement in this file:

Append = "mem = xxM"

Xx indicates the memory size of your computer (in MB ).

To make the changes to "/etc/lilo. conf" take effect, run the command lilo again to check whether the configuration is correct and then restart the machine. You can use one of the following two commands to check whether the configuration takes effect.

$ Cat/proc/meminfo

$ Free

To uninstall Linux, run fdisk/MBR in DOS or MS Windows to uninstall LILO. Then, use fdisk to delete Linux partitions and recycle hard disk space.

In Linux, LILO is an important file used to realize coexistence of multiple operating systems. LILO is short for Linux Loader and used for multiple choices during system loading and startup, if you have installed multiple operating systems, you can use LILO to select which operating system to enter during startup.

Red-Flag Linux desktop 2.4 provides the graphical startup configuration tool "Klilo", which can manage most of LILO's attributes and has friendly interfaces and convenient operations. However, if you are familiar with LILO configurations, you can use manual configuration to configure your machine more accurately.

You can modify LILO by modifying the File "/etc/lilo. after the modification is complete, run the "lilo" command. In LILO, the typical pilot mode consists of two parts: one is started with "image =", used to guide Linux, and the other starts with "other =", used to guide DOS or Windows.

In LILO, the default boot system is ranked first. to modify the default boot system, you only need to switch the positions of the two parts.

LILO usually displays some prompt information on the screen when guiding the system. LILO will keep the information on the screen for a period of time so that you can see it clearly.

Similarly, after modifying the File "/etc/lilo. conf", run the LILO command again to make it take effect.

In some cases, if the physical memory is greater than 64 MB, LILO may not detect all the memory, but uses the first 64 MB memory in the default configuration, run the following command to know how much memory is used in Linux:

$ Cat/proc/meminfo

If the above problem occurs, you can modify/etc/lilo. the conf file solves this problem by adding a similar statement before the first "image =" statement in this file:

Append = "mem = xxM"

Xx indicates the memory size of your computer (in MB ).

To enable "/etc/lilo. conf "changes take effect. you need to re-run the command lilo to check whether the configuration is correct, and then restart the machine. you can use one of the following two commands to check whether the configuration takes effect.

$ Cat/proc/meminfo

$ Free

If you want to uninstall Linux, you can run fdisk/MBR in DOS or MS Windows to uninstall LILO, and then use fdisk to delete Linux partitions and recycle hard disk space.