Link aggregation group as a trunk Link

 


Switch SWA configuration content: www.2cto.com Switch> en
Switch> enable
Switch # conf
Switch # configure
Starting ing from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Switch (config) # h
Switch (config) # hostname SWA
SWA (config) # in vl
SWA (config) # in vlan 1
SWA (config-if) # ip add 192.168.1.101 255.255.255.0
SWA (config-if) # no shu
SWA (config-if) # no shutdownSWA (config-if) # ex
SWA (config) # sp
SWA (config) # spanning-tree m
SWA (config) # spanning-tree mode r
SWA (config) # spanning-tree mode rapid-pvst
SWA (config) # in f0/23
SWA (config-if) # channel-g
SWA (config-if) # channel-group 1 m
SWA (config-if) # channel-group 1 mode d
SWA (config-if) # channel-group 1 mode desirableSWA (config-if) # ex
SWA (config) # in f0/24
SWA (config-if) # channel-g
SWA (config-if) # channel-group 1 m
SWA (config-if) # channel-group 1 mode d
SWA (config-if) # channel-group 1 mode desirableSWA (config-if) # ex
SWA (config) # vl
SWA (config) # vlan 100
SWA (config-vlan) # exit
SWA (config) # vl
SWA (config) # vlan 200
SWA (config-vlan) # ex
SWA (config) # in r
SWA (config) # in range f0/1-8
SWA (config-if-range) # sw
SWA (config-if-range) # switchport
SWA (config-if-range) # switchport access v
SWA (config-if-range) # Switch Port access vlan 100
SWA (config-if-range) # ex
SWA (config) # in r
SWA (config) # in range f0/9-16
SWA (config-if-range) # sw
SWA (config-if-range) # switchport
SWA (config-if-range) # switchport access v
SWA (config-if-range) # Switch Port access vlan 200
SWA (config-if-range) # ex
SWA (config) # in p
SWA (config) # in port-channel 1
SWA (config-if) # sw
SWA (config-if) # switchport m
SWA (config-if) # switchport mode t
SWA (config-if) # switchport mode trunkSWA (config-if) # switchport trunk allowed vlan all
SWA (config-if) # ex
SWA (config )#

Switch SWB configuration content: www.2cto.com witch> en
Switch> enable
Switch # conf
Switch # configure
Starting ing from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Switch (config) # h
Switch (config) # hostname SWB
SWB (config) # in vl
SWB (config) # in vlan 1
SWB (config-if) # ip add 192.168.1.102 255.255.255.0
SWB (config-if) # no shu
SWB (config-if) # no shutdownSWB (config-if) # ex
SWB (config) # sp
SWB (config) # spanning-tree m
SWB (config) # spanning-tree mode r
SWB (config) # spanning-tree mode rapid-pvst
SWB (config) # in f0/23
SWB (config-if) # channel-group 1 mode desirable
SWB (config-if) # ex
SWB (config) # in f0/24
SWB (config-if) # channel-g
SWB (config-if) # channel-group 1 m
SWB (config-if) # channel-group 1 mode d
SWB (config-if) # channel-group 1 mode desirableSWB (config-if) # ex
SWB (config) # vl
SWB (config) # vlan 100
SWB (config-vlan) # ex
SWB (config) # vl
SWB (config) # vlan 200
SWB (config-vlan) # ex
SWB (config) # in r
SWB (config) # in range f0/1-8
SWB (config-if-range) # sw
SWB (config-if-range) # switchport
SWB (config-if-range) # switchport access v
SWB (config-if-range) # Switch Port access vlan 100
SWB (config-if-range) # ex
SWB (config) # in r
SWB (config) # in range f0/9-16
SWB (config-if-range) # sw
SWB (config-if-range) # switchport
SWB (config-if-range) # switchport access v
SWB (config-if-range) # Switch Port access vlan 200
SWB (config-if-range) # ex
SWB (config) # in port-channel 1
SWB (config-if) # switchport mode trunk
SWB (config-if) # switchport trunk allowed vlan all
SWB (config-if) # ex
SWB (config )#