Linux boot Error

Linux boot errors-general Linux technology-Linux technology and application information. For more information, see the following section. . An error is reported when using the CF card.

Inux version 2.6.22.14HingeSoftware (guodemo @ hgsa) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4) #4 SMP Wed Dec 5 23:41:28 CST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000-00000000000a0000 (usable)
BIOS-e820: 00000000000f0000-0000000000100000 (reserved)
BIOS-e820: 0000000000100000-000000001f7f0000 (usable)
BIOS-e820: 000000001f7f0000-000000001f7f3000 (acpi nvs)
BIOS-e820: 2017100001f7f3000-2017100001f800000 (ACPI data)
BIOS-e820: 201710000fec00000-0000000100000000 (reserved)
0 mb highmem available.
503 mb lowmem available.
Found smp mp-table at 000f4f80
Zone PFN ranges:
DMA 0 to> 4096
Normal 4096-> 129008
HighMem 129008-> 129008
Early_node_map [1] active PFN ranges
0: 0-> 129008
DMI 2.2 present.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
Oem id: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Allocating PCI resources starting at 20000000 (gap: 1f800000: df400000)
Built 1 zonelists. Total pages: 128001
Kernel command line: root =/dev/ram0 rw console = ttyS0, 115200
Enabling fast FPU save and restore... done.
Enabling unmasked simd fpu exception support... done.
Initializing CPU #0
PID hash table entries: 2048 (order: 11,819 2 bytes)
Detected 2392.386 MHz processor.
Console: color dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 496136 k/516032 k available (2228 k kernel code, 19392 k reserved, 760 k data, 244 k init, 0 k highmem)
Virtual kernel memory layout:
Fixmap: 0xfff88000-0xfffff000 (476 kB)
Pkmap: 0xffc00000-0xffe00000 (2048 kB)
Vmalloc: 0xe0000000-0xffbfe000 (507 MB)
Lowmem: 0xc0000000-0xdf7f0000 (503 MB)
. Init: 0xc03f2000-0xc042f000 (244 kB)
. Data: 0xc032d30c-0xc03eb5ac (760 kB)
. Text: 0xc0100000-0xc032d30c (2228 kB)
Checking if this processor honors the WP bit even in supervisor mode... OK.
Calibrating delay using timer specific routine .. 4787.69 BogoMIPS (lpj = 23938475)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Trace cache: 12 K uops, L1 D cache: 8 K
CPU: L2 cache: 128 K
CPU: Hyper-Threading is disabled
Compat vDSO mapped to ffffe000.
Checking 'hlt 'instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 13 k freed
CPU0: Intel (R) celon (R) CPU 2.40 GHz stepping 07
Total of 1 processors activated (4787.69 BogoMIPS ).
ExtINT not setup in hardware but reported by MP table
ENABLING IO-APIC IRQs
.. TIMER: vector = 0x31 apic1 = 0 pin1 = 2 apic2 = 0 pin2 = 0
Brought up 1 CPUs
NET: Registered protocol family 16
PCI: pci bios revision 2.10 entry at 0xfb350, last bus = 1
PCI: Using configuration type 1
Setting up standard PCI resources
SCSI subsystem initialized
Usbcore: registered new interface driver usbfs
Usbcore: registered new interface driver hub
Usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
PCI: Transparent bridge-0000: 00: 1e. 0
PCI: Using IRQ router PIIX/ICH [8086/24 c0] at 0000: 00: 1f. 0
PCI-> apic irq transform: Route :00:02. 0 [A]-> IRQ 16
PCI-> apic irq transform: 0000: 00: 1d. 0 [A]-> IRQ 16
PCI-> apic irq transform: 0000: 00: 1d. 1 [B]-> IRQ 19
PCI-> apic irq transform: 0000: 00: 1d. 7 [D]-> IRQ 23
PCI-> apic irq transform: 0000: 00: 1f. 1 [A]-> IRQ 16
PCI-> apic irq transform: 0000: 00: 1f. 3 [B]-> IRQ 17
PCI-> apic irq transform:. 0 [A]-> IRQ 16
PCI-> apic irq transform:. 0 [A]-> IRQ 17
PCI-> apic irq transform:. 0 [A]-> IRQ 18
PCI-> apic irq transform:. 0 [A]-> IRQ 19
PCI: Bridge: 0000: 00: 1e. 0
IO window: c000-cfff
MEM window: ec000000-edffffff
Time: tsc clocksource has been installed.
PREFETCH window: 20000000-200fffff
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
Checking if image is initramfs... it is
Freeing initrd memory: 11335 k freed
Io scheduler noop registered
Io scheduler anticipatory registered
Io scheduler deadline registered
Io scheduler cfq registered (default)
Real Time Clock Driver v1.12ac
Intel_rng: FWH not detected
WDT driver for the Winbond (TM) W83627HF/THF Super I/O chip initialising.
W83627hf/thf WDT: initialized. timeout = 60 sec (nowayout = 0)
W83167hf/hg WDT: WDT driver for w83167hf/HG initializing
W83167hf/hg WDT: I/O address 0x2e already in use
W83167hf/hg WDT: No w83167hf/HG cocould be found
SoftDog: cannot register miscdev on minor = 130 (err =-16)
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds ).
Hangcheck: Using get_cycles ().
Serial: 8250/16550 driver $ Revision: 1.90 $4 ports, IRQ sharing enabled
Serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 1 RAM disks of 65536 K size 1024 blocksize
Intel (R) PRO/1000 Network Driver-version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
E1000:. 0: e1000_probe: (PCI: 33 MHz: 32-bit) 00: 0e: f5: 00: f6: e8
E1000: eth0: e1000_probe: Intel (R) PRO/1000 Network Connection
E1000:. 0: e1000_probe: (PCI: 33 MHz: 32-bit) 00: 0e: f5: 00: f6: e9
E1000: eth1: e1000_probe: Intel (R) PRO/1000 Network Connection
E1000: Starting :0:04. 0: e1000_probe: (PCI: 33 MHz: 32-bit) 00: 0e: f5: 00: f6: ea
E1000: eth2: e1000_probe: Intel (R) PRO/1000 Network Connection
E1000:. 0: e1000_probe: (PCI: 33 MHz: 32-bit) 00: 0e: f5: 00: f6: eb
E1000: eth3: e1000_probe: Intel (R) PRO/1000 Network Connection
Ethernet Channel Bonding Driver: v3.1.3 (June 13,200 7)
Bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! See bonding.txt for details.
E100: Intel (R) PRO/100 Network Driver, 3.5.17-k4-NAPI
E100: Copyright (c) 1999-2006 Intel Corporation
GDT-HA: Storage RAID Controller Driver. Version: 3.05
GDT-HA: Found 0 PCI Storage RAID Controllers
St: Version 20070203, fixed bufsize 32768, s/g segs 256
SCSI Media Changer driver v0.25
Scsi0: ata_piix
Scsi1: ata_piix
Ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14
Ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15
Ata1.00: CFA: SanDisk SDCFH-1024, HDX 4.09, max MWDMA2
Ata1.00: 2001888 sectors, multi 0: LBA
Ata1.00: configured for MWDMA2
Ata2.00: ATA-7: st%215a, 3.AAD, max UDMA/100
Ata2.00: 156301488 sectors, multi 16: LBA48
Ata2.00: limited to UDMA/33 due to 40-wire cable
Ata2.00: configured for UDMA/33
Scsi 0: 0: 0: 0: Direct-Access ATA SanDisk SDCFH-10 hdx pq: 0 ANSI: 5
Sd 0: 0: 0: 0: [sda] 2001888 512-byte hardware sectors (1025 MB)
Sd 0: 0: 0: 0: [sda] Write Protect is off
Sd 0: 0: 0: 0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Sd 0: 0: 0: 0: [sda] 2001888 512-byte hardware sectors (1025 MB)
Sd 0: 0: 0: 0: [sda] Write Protect is off
Sd 0: 0: 0: 0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
The following error message is displayed:
Sda: <3> ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA2
Ata1: EH complete
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA2
Ata1: EH complete
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA2
Ata1: EH complete
Ata1.00: limiting speed to MWDMA1: PIO4
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA1
Ata1: EH complete
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA1
Ata1: EH complete
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA1
Sd 0: 0: 0: 0: [sda] Result: hostbyte = 0x00 driverbyte = 0x08
Sd 0: 0: 0: 0: [sda] Sense Key: 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex ):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 00
Sd 0: 0: 0: 0: [sda] ASC = 0x0 ASCQ = 0x0
End_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
Ata1: EH complete
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA1
Ata1: EH complete
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA1
Ata1: EH complete
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA1
Ata1: EH complete
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA1
Ata1: EH complete
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA1
Ata1: EH complete
Ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
Ata1.00: cmd c8/00: 08: 00: 00: 00/00: 00: 00: 00: 00: 00/e0 tag 0 cdb 0x0 data 4096 in
Res 40/00: 00: 00: 00: 00/00: 00: 00: 00: 00/00 Emask 0x4 (timeout)
Ata1: soft resetting port
Ata1.00: configured for MWDMA1
Sd 0: 0: 0: 0: [sda] Result: hostbyte = 0x00 driverbyte = 0x08
Sd 0: 0: 0: 0: [sda] Sense Key: 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex ):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 00
Sd 0: 0: 0: 0: [sda] ASC = 0x0 ASCQ = 0x0
End_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
Ata1: EH complete
Unable to read partition table
Sd 0: 0: 0: 0: [sda] Attached SCSI removable disk
Sd 0: 0: 0: 0: Attached scsi generic sg0 type 0
Scsi 1: 0: 0: 0: Direct-Access ATA ST380215A 3.AA PQ: 0 ANSI: 5
Sd 1: 0: 0: 0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
Sd 1: 0: 0: 0: [sdb] Write Protect is off
Sd 1: 0: 0: 0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Sd 1: 0: 0: 0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
Sd 1: 0: 0: 0: [sdb] Write Protect is off
Sd 1: 0: 0: 0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Sdb:
Sd 1: 0: 0: 0: [sdb] Attached SCSI disk
Sd 1: 0: 0: 0: Attached scsi generic sg1 type 0
Ehci_hcd 0000: 00: 1d. 7: EHCI Host Controller
Ehci_hcd 0000: 00: 1d. 7: new USB bus registered, assigned bus number 1
Ehci_hcd 0000: 00: 1d. 7: irq 23, io mem 0xee080000
Ehci_hcd 0000: 00: 1d. 7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Usb usb1: configuration #1 chosen from 1 choice
Hub 1-. 0: USB hub found
Hub 1-0: 1. 0: 4 ports detected
Usbcore: registered new interface driver libusual
Input: PC Speaker as/class/input/input0
Pktgen v2.68: Packet Generator for packet performance testing.
Nf_conntrack version 0.5.0 (4031 buckets, 32248 max)
Ip_tables: (C) 2000-2006 Netfilter Core Team
Arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI sort cut mode
Freeing unused kernel memory: 244 k freed
Start init process
Command = '/etc/linuxrc' action = 1 tty = '/dev/null'
Command = '/etc/rc. local' action = 16 tty ='/dev/null'
Command = '/sbin/getty 115200 ttyS0' action = 2 tty = '/dev/null'
Command = '/sbin/getty 115200 ttyS1' action = 2 tty = '/dev/null'
Command = '/sbin/getty tty1' action = 2 tty = '/dev/1'
Command = '/sbin/g

Please help me analyze it. Thank you.