Linux network card (set Gigabit NIC speed and mode)

Source: Internet
Author: User

Ethtool is a command for querying and setting network card parameters.

Profile:

Ethtool EthX//Query EthX network Port basic settings

ETHTOOL–H//Show command Help for Ethtool

Ethtool–i EthX//query EthX information about the network port

Ethtool–d EthX//Query EthX network Port registration information

Ethtool–r EthX//Reset EthX mesh to Adaptive mode

Ethtool–s EthX//Query EthX network Port receipt Package statistics

Ethtool–s EthX [Speed 10|100|1000]\//Set network port rate 10/100/1000m

[Duplex half|full]\//Set network port half/full Duplex

[Autoneg on|off]\//Set the network port for self-negotiation

[Port tp|aui|bnc|mii]\//Set network Port type

[Phyad n]\

[Xcvr internal|exteral]\

[Wol p|u|m|b|a|g|s|d ...] \

[Sopass xx:yy:zz:aa:bb:cc]\

[Msglvl N]

Example:

1) [[email protected]/]# Ethtool eth1

Settings for eth1:

Supported ports: [TP]

Supported Link Modes:10baset/half 10baset/full

100baset/half 100baset/full

1000baset/full

Supports Auto-negotiation:yes

Advertised Link Modes:10baset/half 10baset/full

100baset/half 100baset/full

1000baset/full

Advertised Auto-negotiation:yes

speed:1000mb/s

Duplex:full

Port:twisted Pair

phyad:0

Transceiver:internal

Auto-negotiation:on

Supports WAKE-ON:UMBG

Wake-on:d

Link Detected:yes

2) [[email protected]/]# ethtool-i eth1

driver:e1000

Version:5.0.43-k1

firmware-version:n/a

bus-info:06:08.1

3) [[email protected]/]# ethtool-s eth1

NIC Statistics:

rx_packets:58068300

tx_packets:87124083

rx_bytes:1589713008

tx_bytes:2165825901

rx_errors:0

tx_errors:0

rx_dropped:0

tx_dropped:0

multicast:0

collisions:0

rx_length_errors:0

rx_over_errors:0

rx_crc_errors:0

rx_frame_errors:0

rx_fifo_errors:0

rx_missed_errors:0

tx_aborted_errors:0

tx_carrier_errors:0

tx_fifo_errors:0

tx_heartbeat_errors:0

tx_window_errors:0

4) [[email protected]/]# ethtool-s eth1 Autoneg off speed + duplex full

Related:

1) [[email protected]/]# which Ethtool

/sbin/ethtool

2) [[email protected]/]# Rpm-qf/sbin/ethtool

Ethtool-1.6-5

3) How to make Ethtool settings permanently stored in network devices?

Workaround One:

Ethtool settings can be saved through the/etc/sysconfig/network-scripts/ifcfg-ethx file to activate the option the next time the device starts.

Example: ethtool-s eth0 speed of duplex full Autoneg off

This instruction sets the eth0 device to full-duplex adaptive at a speed of 100Mbs. To set these parameters eth0 startup, modify the file/etc/sysconfig/network-scripts/ifcfg-eth0, adding the following line:

Ethtool_opts= "Speed of duplex full Autoneg off"

Workaround Two:

Writes the Ethtool settings to the/etc/rc.d/rc.local.


This article is from the "I Learn my use" blog, please be sure to keep this source http://593095349.blog.51cto.com/8497121/1603746

Linux network card (set Gigabit NIC speed and mode)

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.