Multiple Models of ADSL route settings graphic tutorial page 1/2

Source: Internet
Author: User
Tags ftp access

ZTE 831 adsl modem

Set 831:
First, we need to refresh the 831 built-in software to 2. Version 79, which can be downloaded at www.zte.com.cn (how to click here)
831 the IP address of the factory Ethernet port is 192. 168. 1. 1. In order to access 831 via telnet, we should set the address of a computer to 192 first. 168. 1. * Run ping 192.168.1.1 to check whether the access Traffic reaches 831. If no problem persists, run telnet 192.168.1.1 in DOS mode. If you have just installed the software, you have a password, the original factory password is adsl831. Then we have logged on to 831. Its prompt is as follows:

>
We can use the help command to get a general idea of the commands we can use. I will not talk about it anymore.
How to Set:
Mode
The problem is whether you select the bridge mode or the route mode. Select r and press Enter.
> R1483 press ENTER
R1483> delwanip all press ENTER
(This statement is used to clear the Setting data. If an error is followed, you must call this command again)
R1483> home Press ENTER
>
Next, let's make quick settings.
Quick press ENTER
The system will ask you how to connect to the WAN. We chose pppoe.
The system asked the Ethernet Ip address again: we hit 192. 168. 1. 1 (must be typed)
Next, ask the subnet mask: We play 255. 255. 255. 0
VPI: 8
VCI: 81
Authentication (Authentication method), we play p,
Then we asked our User name: (the number of hits, the following two items are the same)
Password:
Duplicate password:

Now, you can press y to save all the settings. The system also asked us if we want to continue the quick setting. Answer n

We will execute the save command now, or we will work hard on the white. At this time, 831 is started to restart. Then our TELNET connection will naturally be disconnected. After 831 is restarted, we will continue to telnet and use the show command to check the current situation. If there is no problem, we can see the IP address of the pppoe interface. Congratulations! Your 831 has already dial-up Internet access. How many IP addresses do you see ???, You can unplug the power of 831 and then plug it in.

After such a setup, we only need to set it in the TCP/IP settings on the computer.
IP Address: It can be 192. 168. 1. 2 to 192. 168. 1. 254
Subnet Mask: 255. 255. 255. 0
Default Gateway: 192. 168. 1. 1
DNS: 202.96.209.5
202.96.199.20.
Now, you can surf your computer.

Now let's talk about advanced settings:
Advanced Settings can use dhcp, so that your computer can automatically obtain the ip address. Enable your computer to act as a server, such as opening an ftp server

How to Do dhcp server:
Telnet to 831
> Lan
> Lan> dhcpserver 192.168.1.2 192.168.1.254
> Lan> dhcpserver dns 202.96.209.3 202.96.199.20.
> Lan> home
> Save

It's over. 831 will automatically restart. Generally, 831 will not dial after restart, so you need to unplug the power supply.

If you have servers (such as ftp) in the Intranet)
Telnet to 831
> Pat
> Pat> addpatin pppoe 21/tcp 192.168.1.5
(This means 192. 168. 1. 5. Port 21 is available for ftp service on the computer)
> Pat> home
> Save
Okay, everything is done.

Up to 2110 route settings
Run the "adsl configuration program" file. The page is displayed.

Enter the Ethernet port IP address of the adsl modem in the edit box. (If this item is not changed during the first configuration or configuration, the default value on the interface is the correct IP address. If you have modified this item, enter the last modified value). Make sure that the value is correct. Otherwise, the MODEM cannot be connected through the configuration program and cannot be configured. If the user forgets the IP address of the network port, press the "RESIP" button on the device backboard to restore the IP address of the factory-configured network port (192.168.10.1 ).
During the first operation, the default value of adsl modem is 192.168.10.1. You need to change the ip nic address of the PC to the IP address of the same network segment, and then modify it from the configuration program as needed.
After filling in the IP address, click "Next ". After the program is successfully connected to ADSL, the program reads the status and parameters of the current ADSL and displays the interface shown in Figure 2:

On this page, you can select the encapsulated protocol (provided by China Telecom). The following protocol types are available:
RFC1483 BRIDGE: Single-host BRIDGE access. In this way, only one client can be connected to the WAN through an adsl modem in bridging mode.
RFC1577 ROUTER: IPOA access. In this way, a client can access the WAN through an adsl modem in IPOA mode, or several clients can connect to the WAN through a HUB through an adsl modem in IPOA mode.
RFC2364 ROUTER: PPPOA access. In this way, a client can be connected to the WAN through an adsl modem in PPPOA mode, or several clients can connect to the WAN through a HUB through an adsl modem in PPPOA mode.
If you want to route the Internet, select RFC2364 ROUTER.

On this interface, you can complete the PVC parameter settings for the adsl modem. For a friend in Wuhan, enter 32
At this time, the ADSL Wan port is based on the PPPOA protocol, and there is no need to set the line IP address, line subnet mask, etc., it will be dynamically allocated a line IP address during dial-up. Therefore, you only need to enter the Internet port IP address of the adsl modem in the edit box on this interface (you do not need to modify it for Wuhan friends) and the dialing Internet user name and password provided by China Telecom.
After entering the parameters, click "finish". The configuration program begins to configure the parameters of the adsl modem,

After configuring the adsl modem, the following message is displayed:

Datang Telecom A-400 open Routing
Because there are no more cats at hand, we can only take this as an example. Its settings are concise and clear, but there are few functions!
The WEB setting interface, as its name implies, uses a browser for connection settings!
According to the default IP address of the manufacturer in the instruction. Enter 192.168.1.1 in the address bar of the browser and press enter to enter the settings page! (If a connection fails, set the nic ip address to 192.168.1.X (2-255). The network interface is displayed. The network login box is displayed, prompt to add the account and password given by the manufacturer, and then confirm!
The above description has the same meaning for all the connections to the ADSL cat or router, but may have different default IP addresses, accounts, and passwords according to the factory settings!
After entering, the following interface will appear, but the interfaces made by various manufacturers are not the same. Some may even make more functions, but the main functions are similar!
The default status is the top 1483 bridging mode, that is, the routing mode is not enabled!
The following is the "2516PPPoE" mode. This is the virtual dialing routing mode!
After selection, the following settings will add an "Account" and "password" input box! Enter the account and password provided by China Telecom. The following DNS can be entered as the DNS of China Telecom! The value after "VPI" and "VCI" must be the same as that of China Telecom. You can ask China Telecom to give it to you! But most China Telecom uses the default value!
After saving the settings, the routing is enabled, which is very simple. Other Cats may have different page designs, but the basic settings are the same!
The following is a simple route setting for a fixed IP address. You only need to select the 1577 route mode or the 1483 route mode, and then the following setting box appears, in fact, some manufacturers do not see such numbers as 1577,1483 on the page, but simply write them as static IP addresses or wan ip addresses. These are fixed IP settings page!
VPI, VCI, Encapsulation Format needless to say, cannot be entered incorrectly!
The following Wan IP address, mask, gateway, and DNS must be specified by China Telecom!
Click Save to implement the routing function!
Below are the settings for the cat's Lan, which are generally available by default!
The above shows the cat's IP address.
DHCP is automatically assigned or manually assigned to the IP address mode. The number of sub-hosts is also supported! Because the routing function provided by the cat is relatively simple, generally there are not many sub-machines supported, generally around 30. For example, the maximum number of sub-machines for the cat is 20, more problems may occur, such as connection failure or serious packet loss. You can test the number of supported sub-hosts on your own!

In "status monitoring", network connections and data transmission traffic accumulation are usually displayed! There are also functions such as displaying route tables!
The "account password" is displayed on the "cat Settings" Page. By default, the account password set by the manufacturer can be changed. You can give it as needed!

Utstarcom adsl Routing

Set the nic ip address to 192.168.1.3, subnet 255.255.0, and add 192.168.1.1 to the address bar of the browser, with the username admin and password utstar to go to the web page.

Then there is the "Lan" option, which does not need to be changed!

Then there is the WAN option, which is the focus of the change! Enable the "atm vcc" option under "Wan,

Point to add, the following interface appears, fill in VPI/VCI value, Note: If in the aal5-1 ~ There are VPI/VCI between aal5-4 and you are the same, you must change it to something else, you can add your !!

Next, the "PPP" item of the "Wan" will delete the only protocol in it!

In the "EOA" item of "Wan,

Click "add". The interface must be added in "atm vcc. Select the default route!

Click "DNS" of "service" to add the DNS of China Telecom.

Do not forget. After completing each step, you must "Submit" and click "Submit" in "manage". After the submission is successful, click "Save and restart ", the rest do not need to be changed. Restart the ADSL and the sub-device again after power-off. Wait for 5 ~ 6 minutes. All right. The route is successful. It can be found in 192.168.1.3 ~ You can access the Internet between 192.168.1.254 ~!!

Asus AAM6000EV

Configure the IP address of the computer Nic as 192.168.1.2 mask: 255.255.255.0. If PPPoE virtual dialing software is installed, do not fill in the gateway. For any routing mode. The default gateway is 192.168.1.1.

Open the PC browser, enter 192.168.1.1 in the address bar, and press Enter. In the prompt window, enter the username "root" and password "root" (or adsl/adsl1234 ). The configuration homepage of the ADSL Router appears.

There are two PPPoE access methods:
1. Establish a connection through the virtual dial-up of the PC and share the connection with multiple users through the proxy server. For details about the vro configuration process, see section 7.
2. Use the PPPoE Client built in the ADSL Router to establish a PPP connection with the local server and use the NAT protocol for multi-user sharing.
Now we will introduce the configuration in the second mode.

● Create a PVC channel for PPPoE. If the PVC channel is not in the factory setting value, follow the steps described above->. If the factory configuration already has the corresponding PVC settings, follow the bridge menu to delete the 1483B link-> 1483B to delete the corresponding 1483B interface.

● In the WAN form, click PPP and click Add. The PPP configuration page is displayed. Enter the corresponding value:
PPP Interface: PPP connection no. 0 ~ 7
Atm vc: available PVC Channel
IPF Type: select Public
Status: Select Start or StartOnData.
Protocol: Select PPPoE
Service Name: Optional
Use Dhcp: If enable is enabled, the router obtains information other than the IP address.
Use DNS: If it is enabled, the DNS information obtained from PPP is allocated to the LAN user as the DNS information of the DHCP Server on the router.
Default Route: Select Enable
Security Protocol: set according to the authority authentication method
Login Name: User Name
Password: Password
Submit
To save the configuration, in the Admin form, Click Commit & Reboot and click Submit. Complete Configuration

Kemaiyi Tong KM300A-G

1. The default IP address of this ADSL instance is 192.168.1.1. Therefore, before setting the IP address, set your host to 192.168.1.x (x can be any value ranging from 2 to 255) and set mask to 255.255.255.0. Enter 192.168.1.1 in IE to enter the configuration interface. The default user name and password are all root.
If you have changed the default IP address of ADSL, please log in with your own method.

2. If you have modified this cat, go to "manage \ submit & restart", select "restart mode" as "reboot from default configuration", and click restart. After a while, press 1 to log on again.
In this step, only the default settings are restored. To reduce unnecessary troubles.
3. On the device information page of the home page (for the configured Interface), follow the instructions below to set the settings. This figure is used as a reference.

4. Pay attention to the 3 circled in red. The default value is 8/35, and China Telecom uses exactly 8/35. Therefore, we need to modify this value. If China Telecom on your side is not the value, modify the item that exactly corresponds to this value. If there is no value provided by China Telecom, do not modify it.
Modification method:
5. Click quick settings on the homepage.
Set the red part according to the value provided by China Telecom.
Select 5 for the ATM interface, because the system already occupies four accounts and cannot be used.
Select enable in Operation Mode
Choose disible for brige.

6. After you click confirm in the previous step, items 1 and 2 in the first figure will appear in the device information on the home page. After a while, the status light of the first item will change to green, it indicates that the number has been automatically pulled, and the IP address is automatically obtained.
Sometimes Step 1 may fail. You can disconnect the ADSL power first and try again. However, make sure that the ATM interface is not in use, and the VPI/VCI combination does not appear in other interfaces.

7. Set the LAN to DHCP mode in this step, which saves a lot of trouble.
Select "DHCP Server" as the DHCP mode in the local network/DHCP mode, and press OK.

8. The current homepage/device information is shown in every figure.
Now, at the top of the "route/IP Route" field, there will be an item with a goal and a network mask of 0. And there are several items with your dynamic IP address. This is the success!
Finally, click submit in "manage/submit & restart", submit your modifications, and then click restart to write your modifications to the cat's memory. After a while, the cat will automatically dial the number online and start routing.

9. Finally, set the client:
Dynamic IP: the IP address of the client is automatically obtained, and the DNS is automatically obtained.
Static IP: the IP address of the client is set to the IP address on the same network segment as the MODEM, And the gateway and DNS are set to the modem address. Everything is OK!
I have been busy for a long time. I should have done it. I don't know if there are any omissions? I hope you can add it!

Asus aam6000ev

My younger brother recently installed and debugged several units that use adsl for network construction. I recommend aam6000ev of Asus (simple menu and all Chinese). Now, adsl has developed rapidly in many major cities, therefore, the adsl mode/vro will be on fire. I will talk about it as follows:
1. Enter the WAN settings and select the atm interface. The value of vpi/vci is determined. (We generally use vpi: 8, vci: 35 in Qingdao, IP address, subnet mask default (fill in if it is a leased line), Qos type, Pcr are all default, IGMP, NAT, default route select enabel, gateway IP address default, user name, the password is already provided to you when installing adsl, the status is start, the automatic dns is selected to permit, the primary dns, the secondary dns asks the local isp, this must be known, (Qingdao is, 202.120.134.68, 202.120.128.68) a new path is displayed on the homepage, and the status is green,
2: You do not need to set the route.
3: Go to the dhcp configuration page, select dhcp server in dhcp Mode
4: you do not need to set the client machine to automatically obtain the ip address. Otherwise, you cannot access the Internet.

HUAWEI (HUAWEI) SmartAX MT800A

Start of work:
After all the lines are connected, set IP Address: 192.168.1.X (X = 2-8) and mask: 255.255.255.0 on the PC.
Gateway: 192.168.1.1 (do not forget to click "add" after entering the gateway; otherwise, no gateway is entered)
After confirming, the system prompts you to restart, enter the system again, open the browser, enter http: // 192.168.1.1 in the address bar, and press ENTER
In this case, the SmartAX MT800A setting screen is displayed. Since it is not difficult to operate in the future, I will not bother

Key: PPPoE Configuration

Step 1 open the Web page "ATM Setting ";

Step 2 select the "PPPoE LLC" option from the drop-down list of the "Connection Type" field;

Step 3: Change the Operation Mode to enable.

Step 4: based on the information provided by the ISP or system supplier, fill in appropriate numeric values in the corresponding fields, such as "VPI", "VCI ", "PPPoE User Name", security protocol, "PPPoE password", and other values, the Default Router (Default route) is changed to enable;

Step 5 enter the correct value and click <"Submit>" below the field to Submit the setting to the input ADSL terminal;

Step 6 ensure that the NAT value is "Enable", which is Enable by default.

In step 7, the default value of DHCP is that "DHCP Server" is not enabled. You can decide whether to enable it as needed.

In step 8, click the "Save & Reboot" Directory on the Web page, select "Reboot" in the "Reboot Mode" dialog box, and click the <Save> button to complete the configuration of the ADSL terminal and Save it permanently ;.

Thank you, amen! After saving the file, go to the webpage and see ~~~~~

Ji Kang UT300R

1. Set VPI and vci in the wan. Follow the local settings (the IP address, mask, and gateway do not need to be set later). 2. Set pppoe llc for the encapsulation protocol, 3. Fill in the user name and password in PPP settings, review and set PAP, and select automatic connection; 4. Set the virtual circuit, which is the most critical step, this is also the main reason why many friends failed to set the circuit. The virtual circuit is divided into 0 ~ 7. Set one according to the local condition (I am here 0, as if many regions are also 0), and select "enable" in the upper left corner of the screen ", the key is that the remaining seven virtual circuits should be closed and set one by one. If you select one, you must choose to close it in the upper left corner. In this case, until you close all the seven unused ones. Remember, commit each time you close one entry. 5. Select NAPT In the NAT console.
By the way, the user name is admin and the password is utstar. In this way, the route settings are successful.

Shanghai Bell CyberLink 6307 YG

1. Make sure that the IP address of the computer Nic is 192.168.1.2, the mask is 255.255.255.0, And the IP address can be pinged to 192.168.1.1.
Set the preferred DNS to 202.96.209.20.
Set the backup DNS to 202.96.209.5
The above 2 DNS are all in Shanghai, other areas can check http://ddj88.myrice.com/internet/broadband/vpi-vci.htm online
2. Run the CLCOM. EXE program to configure the MODEM. The default password is "password"

3. Modify the VPI/VCI values based on the local line parameters, enter the user name and password, and click APPLY to save the settings.
The default value for this cat is 0/35.

Shanghai East District 0/32
Western District 8/81

DNS: 202.96.209.20.
202.96.209.5

Generally, you can use the default settings.

View the route table. If a similar record is displayed, the modification is successful.

Asus AAM6005HW

1. The network environment MODEM is connected to the HUB. The default address of Asus 6005 AAMHW is 192.168.1.1. Here I changed it to 192.168.0.1 and restarted the MODEM.
, I set my machine IP address to 192.168.0.168 255.255.255.0 Default Gateway 192.168.0.1
2. Enter 192.168.0.1 as shown below

User adsl
After the password adsl1234 appears [Note that if your MODEM is restricted, Automatic Virtual dialing may fail. The solution is to download the software and upgrade your MODEM]

3. Click "CHANNEL", click "Action Item", select "DELETE", and click "SUBMIT" to clear the preset settings. When the settings appear,... DONE, click "reset modem" to restart the MODEM,
Click ADD to ADD a new setting after startup, as shown in figure

In particular, the restricted modem I mentioned is here. For example, MODEMSERVICETYPE has six choices, and the restricted MODEM may have only three, we chose the sixth one here. VPI/VCI depends on the local telecom operator. If you do not know the local setting, China Telecom will not tell you, you can go here to see if there will be a http://ddj88.myrice.com/internet/broadband/vpi-vci.htm set up for you.

4. Click "SUBMIT" and set
Area 1: Enter the user name and password when applying for broadband at China Telecom.
Area 2: select UP. [if the setting is correct, you only need to enable the MODEM to automatically log on to the INTERNET within 30 seconds.]
Figure area 3: The first one must be checked, because [NAT enables the MODEM to have port ing function, Auto Discovery DNS From PPP specifies whether the MODEM status can automatically return local DNS information, I may have misunderstood this sentence. If not, please forgive me]

5: Submit this operation again and restart the MODEM.
6: Set your DNS again, such as, if you do not know, I want to still this web site will find the http://ddj88.myrice.com/internet/broadband/vpi-vci.htm this simple, I will not say more, anyway, ask you to restart the MODEM you just restart, I cannot remember if I want to restart it,

7: Check whether your virtual automatic dialing is successful. Click PPP under Statistics and then click STATUS. If yes, your virtual automatic dialing is successful.

8: Well, after the virtual dial-up is complete, now we have to find a way for Internet users to access various types of services through routes. Here, port ing can complete this function.
9: on this page, I have already set up this page. I don't want to delete it any more. I just want you to understand that I have added three ports. If, if you want to add port 22 for other services, write the parameters as shown in the preceding figure, and click Submit.
Note that if you want to DELETE the added port, select delete no for Action: Write the port you want to DELETE, and click Submit, select Action: SAVE and click submit again. If this is not the case, if your MODEM powers down, your settings will be gone. Here, I would like to explain, port 3389, which is a port used by RPC [Remote Desktop]. That is to say, if you want to control this machine on the INTERNET through remote desktop, add this port to facilitate remote maintenance.

10: at this time is to arrange your HTTP/FTP server, such as the installation of SRV-U and IIS, peanut shells and so on here, I will not elaborate on [this kind of tutorial everywhere], note that if this method is set correctly, enter your domain name in your lan. [assume that your domain name is AAA. VICP. NET] You will see the MODEM configuration interface, which is normal, so if you want to test after the customization is complete, only, if the machine on your intranet does not access the server of your domain name [such as dial-up Internet access, to test whether this setting is feasible], check whether it can be accessed normally [of course, if, if you enter the Intranet IP address of your server on your intranet and the server cannot be accessed normally, it is hard to set it again.]
11: Question: here, I want to raise a question. I hope you can explain it to me. I find that I don't know why, after setting the setting, FTP can only be accessed normally if the setting is as follows. I don't know why [if the setting is normal for FTP access, SOCET error will be reported and the list will not be displayed]

Alibaba Carter Speed Touch 515 external PPPoE configuration Manual
Note: If the PVC to be configured already exists during parameter configuration, delete the original link and reconfigure it !!
1. USB Driver Installation
1. Put a USB drive into the drive, double-click setup.exe ";


Click "Next" and connect the Modem and PC with USB cables as prompted. The driver is installed.


3. The driver installation is complete.

Ii. PPPoE parameter configuration
1. Connect the PC and Modem with a USB or Ethernet cable. Use DHCP (you can also manually set the IP address of the PC to 192.168.1.2 and the subnet mask 255.255.255.0 ). Open IE and enter 192.168.1.254 in the address box;


2. Click "Expert Mode" To Go To The following interface. Click "Continue ";


3. Select "Configration"-> "WAN Connections" consecutively, and click "Create a new service ";

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.