Network common word collection

Time/System Time
Date/System Date
Level 2 Cache Level 2 Cache
System Memory
Video Controller
Invalid LCD Panel Model
Audio Controller
Modem Controller Modem)
Primary Hard Drive
Modular Bay module Bracket
Service Tag
Asset Tag
BIOS Version
Boot Order/Boot Sequence startup Sequence (System Searches for operating system files)
Diskette Drive floppy disk Drive
Internal HDD built-in hard drive
Floppy device
Hard-Disk Drive
UNB Storage Device
Drive CD/DVD/CD-RW Drive
CD-ROM device drive
Modular Bay HDD Modular hard drive
Carw.nic carw.bus NIC
Onboard NIC
The level of hardware check during Boot POST self-check: if it is set to "MINIMAL" (default), the self-check is only performed during BIOS upgrade, check is performed only when the memory module is changed or the previous self-check is not completed. If it is set to "THOROUGH", a full set of hardware checks will be performed during self-check.
Config Warnings warning settings: This option is used to set whether to trigger an alarm when the system uses a low-voltage power adapter or other unsupported configurations. It is set to "DISABLED" to disable the alarm, ENABLED
Internal Modem built-in Modem: use this option to enable or disable the built-in Modem. After disabled is disabled, the Modem is invisible to the operating system.
LAN Controller network Controller: use this option to enable or disable the PCI Ethernet Controller. The device is invisible to the operating system after it is disabled.
Pxe bis Policy/pxe bis Default Policy
Pxe bis policy: This option controls how the system handles (starting the overall service Boot Integrity Services (BIS) authorization requests without authentication. The system can accept or reject BIS requests. When it is set to "Reset", BIS will reinitialize and set it to "Deny" the next time you start the computer ".
Onboard Bluetooth
Onboard bluetooth device
MiniPCI Device
Mini PCI device
MiniPCI Status
Mini PCI device status: You can use this option to enable or disable onboard PCI devices when installing a Mini PCI device
Wireless Control
Wireless Control: You can use this option to set the control mode for MiniPCI and Bluetooth wireless devices. When set to "Application", wireless devices can be enabled or disabled through applications such as "Quickset", and hot keys are unavailable. When set to "/Application", wireless devices can be enabled or disabled through applications such as "Quickset" or hot keys. When it is set to "Always Off", the wireless device is disabled and cannot be enabled in the operating system.
Wireless
Wireless Device: use this option to enable or disable wireless devices. This setting can be changed through the "Quickset" or "" hotkey in the operating system. Whether the setting is available depends on the setting of "Wireless Control.
Serial Port
Serial Port: This option can be used to avoid resource conflicts between devices by allocating port addresses or disabling ports.
Infrared Data Port
Infrared data port. You can use this setting to re-allocate the port address or disable the port to avoid resource conflicts between devices.
Parallel Mode
Parallel Port mode. Control Computer Parallel port operation mode is "NORMAL" (AT compatible) (general standard parallel port), "BI-DIRECTIONAL" (PS/2 compatible) (bidirectional mode, allows two-way communication between the host and peripherals) or "ECP" (Extended Capabilities Ports, Extended functional Ports) (default ).
Num Lock
Digital lock. Set whether the digital lamp (NumLock LED) lights up when the system starts. If it is set to "DISABLE", the digital lamp is switched off. If it is set to "ENABLE", the digital lamp is switched on when the system is started.
Keyboard NumLock
Keyboard digital lock: This option is used to set whether to prompt keyboard-related error messages when the system starts.
Enable Keypad
Enable keypad: set to "by numlock" to enable the keypad when the NumLock light is on and the external keyboard is not connected. Set to "Only By Key" to disable the embedded Key zone when NumLock is on.
External Hot Key
External hot key: This setting can be used on the external PS/2 keyboard in the same way as using the key on the laptop. If you use the ACPI operating system in2000 or WinXP, The UNB keyboard cannot use keys. Only the UNB keyboard in pure DOS mode can use keys. Set to "scroll lock" (default option) to enable this function, set to "not installed" to disable this function.
UNB Emulation
UNB simulation: You can use the UNB keyboard, UNB mouse, and UNB soft drive in an operating system that does not directly support UNB. This setting is automatically enabled during BIOS startup. When this function is enabled, the simulation continues to work when the control is transferred to the operating system. If this function is disabled, the simulation is disabled when the control is transferred to the operating system.
Pointing Device
Pointer device: When set to "serial mouse", the external serial mouse is enabled and the integrated touchpad is disabled. When it is set to "PS/2 MOUSE", if the external PS/2 MOUSE, the integrated touchpad is disabled. When set to "TOUCH PAD-PS/2 MOUSE" (default), you can switch between the MOUSE and the touchpad if the external PS/2 MOUSE is used. The change takes effect after the computer restarts.
Video Expansion
Video Extension: You can use this option to enable or disable video extension and adjust lower resolution to higher and normal LCD resolution.
Battery
Battery
Battery Status
Battery status
Power Management
Power Management
Suspend Mode
Pending Mode
AC Power Recovery
AC power recovery: This option can be reflected by the computer when the AC power adapter is plugged back to the system.
Low Power Mode
Low power mode: This option is used to set the power consumption when the system sleep or shuts down.
Brightness
Brightness: This option sets the brightness of the display when the computer starts. When the computer is in the power supply status, the default value is half. The computer is set to maximum by default when the AC power adapter is in the power supply status.
Wakeup On LAN
Network wake-up: This option allows you to wake up your computer from sleep when network signals are connected. This setting is invalid for Standby state. You can only wake up the standby status in the operating system. This setting is only valid when an AC power adapter is attached.
Auto On Mod automatic Boot Mode: Note that if the AC power adapter is not properly connected, this setting will not take effect. This option can be used to set the automatic boot time of a computer. You can set the automatic boot time of a computer every day or only on workdays. The setting takes effect after the computer restarts.
Auto On Time automatic start Time: This option allows you to set the automatic start Time of the system. The Time format is in the 24-hour format. Type a value or use the left and right arrow keys to set the value. The setting takes effect after the computer restarts.
Dock Configuration
Docking Status
Universal Connect interface: If the operating system is WinNT4.0 or earlier, this setting is invalid. If you often use more than one Dell docking station device and want to minimize the initial time for docking, set it to "ENABLED" (default ). If you want the operating system to generate a new system setting file for each new docking device connected to the computer, set it to "DISABLED ".
System Security
Primary Password master Password
Admin Password
Manage passwords
Hard-disk drive password (s) Hard drive password
Password Status: This option is used to lock the system Password when the Setup Password is enabled. Set this option to "Locked" and enable the Setup password to place the system password changed. This option can also be used to place the password disabled when the system starts.
System Password
Setup Password
Post Hotkeys self-check hotkey: This option is used to specify the hotkey (F2 or F12) displayed on the screen during POST ).
Chassis Intrusion
Chassis anti-theft: This option is used to enable or disable the features of the chassis anti-theft detection. When it is set to "Enable-Silent", if the chassis intrusion is detected during startup, no warning message is sent. This field displays "DETECTED" when this option is enabled and the chassis cover is opened ".
Drive Configuration
Drive settings
Diskette Drive A: disk Drive A: If A floppy disk is attached to the system, use this option to enable or disable A floppy disk Drive.
Primary Master Drive first Master Drive
Primary Slave Drive first Slave Drive
Secondary Master Drive Second Master Drive
Secondary Slave Drive second Slave Drive
IDE Drive UDMA supports udma ide drives: This option enables or disables DMA transmission through an internal IDE hard disk interface.
Hard-Disk drive Sequence Hard drive Sequence
System BIOS boot devices System BIOS boot sequence
UNB device
Memory Information
Installed System Memory: This option displays the size and model of Memory in the System.
System Memory Speed
Memory rate: This option shows the memory speed.
System Memory Channel Mode: This option displays Memory slot settings.
Memory Capacity of The AGP Aperture AGP region: This option specifies the memory value allocated to the video adapter. Some video adapters may require more memory than the default value.
CPU information
CPU Speed CPU rate: This option displays the running rate of the central processor after startup
Bus Speed Bus rate: Display processor Bus Rate
Processor 0 ID Processor ID: display the Processor type and model number
Clock Speed Clock frequency
Cache Size Cache value: displays the second-level Cache value of the processor.
 
This article is from the "shenmei Network Technology blog"