Photoshop gives the lawn characters a dark red glow effect Tutorial

A tutorial for users of Photoshop software that adds a dark red glow to the characters on the lawn.

Tutorial Sharing:

1, open the original material large image, create an optional color adjustment layer, green adjustment, parameters and effect of the following figure. This step puts the green in the picture dark and green.

< map 1>

< map 2>

2, press CTRL + J to copy the current optional color adjustment layer, the effect of the following figure.

< map 3>

3, create an optional color adjustment layer, red, yellow, green, green, neutral color adjustment, parameter settings such as Figure 4-8, the effect is shown in Figure 9. This step quickly turns the grass and trees into orange-red color.

< map 4>

< map 5>

< map 6>

< map 7>

< map 8>

< map 9>

4, press CTRL + ALT + 2 to call up the high light constituency, press CTRL + Shift + I to select the dark selection, and then create the curve adjustment layer, the RGB, red, blue channel adjustment, parameter settings such as Figure 10, determined to use a less transparent black brush to wipe out the forest part, the effect is as shown in Figure 11. This step is mainly to the grass part of the deep pressure dark.

< map 10>

< map 11>

5, press CTRL + ALT + 2 to bring up the highlight selection, and then create brightness/contrast adjustment layer, appropriate increase contrast, parameters and effects as shown below.

< map 12>

< map 13>

6, create an optional color adjustment layer, the red, yellow to adjust, parameter settings such as Figure 14,15, determined to press CTRL + ALT + G to create a clipping mask, the effect is as shown in Figure 16. This step adds a warm color to the picture's high light area.

< map 14>

< map 15>

< map 16>

7, create curve adjustment layer, the RGB, red, blue channel adjustment, parameter settings such as Figure 17, after the mask filled with black, and then with the transparency of the lower soft edge white brush to the bottom and the lower right corner area to wipe out, the effect is shown in Figure 18. This step darkens the bottom area.

< map 17>

< map 18>

8, the background layer to copy a layer, press CTRL + Shift +] top. Enter the channel panel, copy the blue channel and get the blue copy channel. Press CTRL + L to adjust the level of the blue Copy channel, increase the contrast of light and shade, make the sky part white, and the other areas dim, as shown below.

< map 19>

9, with the soft side of the black brush to the sky outside the area painted black, the following figure. Then hold down CTRL + the left mouse button and click on the channel panel blue copy channel thumbnail to load the sky section of the selection.

< map 20>

10, point RGB channel to return to the layers board, a new layer, with the paint bucket tool filled with white, remove the background copy after the selection layer deleted, the effect of the following figure.

< map 21>

11, click the image below to open the big picture of the sky, and then right-click the "Picture Save As", the sky material large picture saved to this machine.

< small map view big picture >

12, with PS to open just save the sky material pictures, with mobile tools dragged in, adjust the position after creating a clipping mask, the effect of the following figure.

< map 22>

13, select the menu: Filter > Blur > Gaussian blur, the value is 5, determine the effect of the following figure. This step blurs the sky.

< map 23>

14, press CTRL + ALT + 2 to bring up the high light selection, press CTRL + Shift + I to select the dark selection, then create the curve adjustment layer, the RGB, blue channel adjustment, parameters and effects as shown below. This step darkens the dark part slightly and adds Blue.

< map 24>

< map 25>

15. Create a new layer, use the elliptical marquee tool to pull out the selection shown in the following figure, feather 45 pixels and fill with orange: #F0856D, after the selection is canceled, the blending mode is changed to "overlay", and the effect is shown below.

< map 26>

16. Press CTRL + J to copy the current layer, press CTRL + T to narrow it down, and then change the blending mode to "color filter", the effect is as follows.

< map 27>

17, press CTRL + J to copy the current layer, press CTRL + T to shrink a bit, lock the pixel area with the paint bucket tool filled with orange: #FAB715, and change the blending mode to "color", the effect of the following figure.

< map 28>

18, press CTRL + J to copy the current layer, press CTRL + T to shrink a little more, the effect of the following figure. These steps add orange-yellow high light to the picture.

< map 29>

19, the background layer to copy a layer, press CTRL + Shift +] top, with the pen tool to pull out the characters, into the selection after adding layer mask, the effect of the following figure.

< map 30>

20, create curve adjustment layer, increase light and shade contrast, parameter settings such as Figure 31, determined after the creation of a clipping mask, the effect is shown in Figure 32. This step increases the character part of the light and shade contrast.

< map 31>

< map 32>

21, and then create curve adjustment layer, the RGB, red, green channel adjustment, parameter settings such as Figure 33, determine after the creation of clipping masks, and then the mask filled with black, and then with the transparency of the lower soft white brush to the character backlight area painted darker, the effect is shown in Figure 34.

< map 33>

< map 34>

22, a new layer, create a clipping mask, the foreground color is set to yellow-brown: #985E32, and then use a lower transparency brush to the right edge of the character to paint the environment color. After the determination of the mixed mode to "strong light", the opacity to: 60%, the effect of the following figure.

< map 35>

23, create brightness/Contrast adjustment layer, the appropriate increase in contrast, parameter settings such as Figure 36, determined after the creation of a clipping mask, the effect is as shown in Figure 37.

< map 36>

< map 37>

24, create an optional color adjustment layer, the blue, white adjustment, parameter settings such as Figure 38,39, after the creation of a clipping mask, the effect is shown in Figure 40. This step darkens the part of the garment.

< map 38>

< map 39>

< map 40>

25, fine tune the complexion, strengthen the character part of the light and shade, the effect of the following figure.

< map 41>

26. Create a new layer, press CTRL + ALT + Shift + E-stamp layer, and blur the next figure selection with the Blur tool.

< map 42>

Finally, rub the skin of the character, strengthen the local light and finish the final effect.

Well, the above information is a small part of the software users of Photoshop to bring the user of the lawn to add a red color effect of the course to share the full content of the tutorial, in general, in the process of the first to add to the image of the light material, and then the main color into orange, and then the whole dark, Partially render some orange-yellow high light, hope to help everyone.